background image

14

02/23

7037-807C

Negative pressure results from the imbalance of air available 

for the appliance to operate properly. It can be strongest in 

lower levels of the house.

Causes include:

•  Exhaust fans (kitchen, bath, etc.)
•  Range hoods
•  Combustion  air  requirements  for  furnaces,  water 

appliances and other combustion appliances

•  Clothes dryers
•  Location of return-air vents to furnace or air conditioning
•  Imbalances of the HVAC air handling system
•  Upper level air leaks such as:

-  Recessed lighting
-  Attic hatch
-  Duct leaks

To minimize the effects of negative air pressure:

•  Install the outside air kit with the intake facing prevailing 

winds during the heating season

•  Ensure  adequate  outdoor  air  for  all  combustion 

appliances and exhaust equipment

•  Ensure furnace and air conditioning return vents are not 

located in the immediate vicinity of the appliance

•  Avoid installing the appliance near doors, walkways or 

small isolated spaces

•  Recessed lighting should be a “sealed can” design
•  Attic hatches weather stripped or sealed
•  Attic mounted duct work and air handler joints and seams 

taped or sealed

J. Negative Pressure

K. Frequently Asked Questions

CONTACT YOUR DEALER

  for  additional  information 

regarding operation and troubleshooting.

Visit 

www.quadrafire.com

 to find a dealer. 

ISSUES

SOLUTIONS

Odor from appliance

When  first  operated,  this 

appliance  may  release  an 

odor for the first several hours. 

This  is  caused  by  the  curing 

of  the  paint  and  the  burning 

off  of  any  oils  remaining  from 

manufacturing.

Metallic noise

Noise  is  caused  by  metal 

expanding  and  contracting  as 

it  heats  up  and  cools  down, 

similar  to  the  sound  produced 

by  a  furnace  or  heating  duct. 

This  noise  does  not  affect  the 

operation  or  longevity  of  the 

appliance.

Whirring sound

If the optional blower has been 

installed, the blower produces a 

whirring sound which increases 

in  volume  as  the  speed  is 

increased.

Table 14.1

Asphyxiation Risk.

•  Negative  pressure  can  cause  spillage 

of  combustion  fumes,  soot  and 

carbon monoxide.

•  Appliance needs to draft properly for safety.

WARNING

Fire Risk.

•  DO  NOT  BURN  GARBAGE  OR 

FLAMMABLE 

FLUIDS 

SUCH  AS 

GASOLINE, NAPHTHA OR ENGINE OIL.

•  Do NOT burn treated wood or wood with 

salt (driftwood).

•  May  generate  carbon  monoxide  if  burn 

material other than wood.

May result in illness or possible death.

WARNING

Fire Risk.

Keep  combustible  materials,  gasoline  and 

other  flammable  vapors  and  liquids  clear 

of appliance.

WARNING

•  Do  NOT  store  flammable  materials  in  the 

appliance’s vicinity.

•  DO  NOT  USE  GASOLINE,  LANTERN  FUEL, 

KEROSENE,  CHARCOAL  LIGHTER  FLUID  OR 

SIMILAR LIQUIDS TO START OR “FRESHEN UP” A 

FIRE IN THIS APPLIANCE.

•  Keep  all  such  liquids  well  away  from  the  appliance 

while it is in use.

•  Combustible materials may ignite.

Summary of Contents for 43ST-ACC-AU



































Reviews: