background image

3

January 10, 2020

7045-910I

4100 Insert ACC

Model:

4100i ACC Wood Insert

Laboratory:

Intertek

Report No:

100428837PRT-001

Type:

Solid Fuel Type, Listed Room 

Heater

Standard:

UL1482 and ULC S628-93 and 

(UM) 84-HUD, Mobile Home 

Approved.

The Quadra-Fire 4100i ACC Wood Insert meets the U.S. Environmental Protection Agency’s crib wood emission  limits 

for wood heaters sold after May 15, 2015.

EPA Certification #:

876

EPA Certified Emissions:

4.3 grams per hour

*LHV Tested Efficiency:

78.5 %

**HHV Tested Efficiency:

72.7 %

***EPA BTU Output:

11,700 to 25,900 / hr.

****Peak BTU/Hour 

Output:

60,500

Vent Size:

6 inches

Firebox Size:

2.43 cubic feet

Recommended Wood 

Length:

18 inches

Fuel Orientation:

Side-to-Side

Fuel

Seasoned Cord Wood

* Weighted average LHV efficiency using Douglas Fir 

dimensional lumber and data collected during EPA 

emissions test.
**Weighted average HHV efficiency using Douglas 

Fir dimensional lumber and data collected during EPA 

emissions test.
***A range of BTU outputs based on EPA Default 

Efficiency and the burn rates from the low and high EPA 

tests, using Douglas Fir dimensional lumber.
****A peak BTU out of the unit calculated using the 

maximum first hour burn rate from the High EPA Test and 

the BTU content of cord wood (8600) times the efficiency.

Important Safety Information

A. Insert Certification

B. BTU & Efficiency Specifications

Approved for ZC fireboxes.

NOTE: 

This installation must conform with local codes. In the absence of local codes you must comply with the 

UL1482, 

(UM) 84-HUD and NPFA211 in the U.S.A. and the ULC S628-93 and CAN/CSA-B365 Installation Codes in 

Canada.

This wood appliance needs periodic inspection and repair for proper operation. Consult the owner’s manual for further 

information. It is against federal regulations to operate this wood heater in a manner inconsistent with the operating 

instructions in the owner’s manual.

Summary of Contents for 41I-ACC-BK



























Reviews: