background image

July 7, 2011

7033-277I

Page  11

3100 Wood Stove Series (ACC)

R

B. Clearances to Combustibles (UL and ULC)

BACKWALL / SIDEWALL 

A

B

C

D

E

F

E

F

CORNER INSTALLATION

G

H

*

90° OFF TOP 

UP & OUT CEILING 

CLEARANCE

STOVE TO CEILING 

CLEARANCE 

C

D

ALCOVE TOP VIEW 

G

A

B

ALCOVE SIDE VIEW

NOTE:  Clearances may only be reduced by means 

approved by the regulatory authority having jurisdiction

Fire Risk.

•  Comply with all minimum clearances to 

combustibles as specified.

•  Failure to comply may cause house fire.

WARNING

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS In Inches & (Millimeters)

 

NOTE:  All "A" , "C" and "F" Dimensions are to the inside diameter of the flue collar. 

 

INSTALLATION: Full Vertical OR Horizontal with Minimum 2 FT Vertical Off Stove Top

SINGLE WALL PIPE

 

    Flat Top Model 

15.25 (387)  11.75 (298)  25.5 (648)  16 (406) 

8 (203) 

17 (432) 

48 (1220)  12 (305)

    Step-Top Model 

12 (305)   8.5 (216) 

22 (559)  12.5 (318) 

5.5 (140  14.5 (368)  48 (1220)  12 (305) 

   

   

DOUBLE WALL PIPE

 

    Flat Top Model 

10.5 (267)  6.5 (165) 

22 (559) 

13 (330) 

6.5 (165)  15.5 (394)  48 (1220) 

9 (229)

    Step-Top Model 

10 (228) 

6 (152) 

20.5 (521)  11 (279) 

4 (102) 

13 (330) 

48 (1220) 

9 (229) 

   

INSTALLATION: 90° Elbow Off Top of Stove Through Backwall

SINGLE WALL PIPE

 

   Flat Top Model 

12 (305) 

8.5 (216) 

22 (559) 

13 (330) 

8 (203) 

17 (432) 

48 (1220)  12 (305)

   Step-Top Model 

10 (254) 

6 (152) 

20.5 (521)  11 (279) 

5.5 (140)  14.5 (368)  48 (1220)  12 (305) 

   

 

DOUBLE WALL PIPE

 

   Flat Top Model 

8 (203) 

4.5 (114)  17.5 (445)  8.5 (216) 

6.5 (165)  15.5 (394)  48 (1220) 

9 (229)

   Step-Top Model 

10 (254) 

6 (152) 

20.5 (521)  11 (279) 

4 (102) 

13 (330) 

48 (1220) 

9 (229) 

INSTALLATION: ALCOVE

  Six inch (6") (152mm) diameter listed Double Wall air insulated connector pipe with UL103 HT* listed 

factory-built Class "A" chimney, or a masonry chimney.  (Mobile Home must be equipped with a spark arrestor). Maximum depth of Alcove 

shall be no more than 48 inches (1220mm) with a minimum height of 48 inches (1220mm) to top of unit, and the referenced clearances.

     *In Canada must comply with CAN/ULC-S269 M87 for the 650

o

C Factory-built chimney.

DOUBLE WALL PIPE

 

    Flat Top Model 

11.75 (298)  8.25 (210)  23.5 (597)  14.5 (368) 

N/A 

N/A 

48 (1220) 

*

    Step-Top  Model 

10 (254) 

6.5 (152)  20.5 (521)  11 (279) 

N/A 

N/A 

48 (1220) 

*

 

* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED

 

 

 

 

 

 

  

NOTE:  Service Space

In order to replace the tube channel assembly a clearance 

of 19 inches (483mm) is required on the right side of stove 

in order to remove the tubes with the stove in place.  
If space is not available, the stove will have to be discon

-

nected from the chimney to proceed with the tube replace

-

ment.

Summary of Contents for 31M-ACC-MBK





















































Reviews: