QTS AN-X2-MOD-MON User Manual Download Page 48

Page: 48 / 61

Page

AN-X2-MOD-MON

May 2016

Counter

Description

was expected

RX CRC ERRORS

Count of received packets with CRC errors

RX ABORT ERRORS

Count of received packets with abort errors

RX NOISE ERRORS

Count of received packets with noise errors

RX PACKET TIMEOUTS

Count of times a packet was transmitted to a drop and no
reply was received

RX OVERRUN

Count of received packets with overrun errors

RX PACKET SHORT

Count of received packets that were shorter than
expected

RX ERROR MASK

High byte shows the cause of protocol errors, low byte
shows drop number -1. Displayed in hex.

DROP ERRORS

The drop error table, in hex

RX PROTOCOL ERRORS Count of received packets that did not make sense in

terms of the S908 network protocol

Ethernet/IP UDP Statistics

The Ethernet/IP Statistics consist of two portions:

•

Global counters

•

Statistics for each connection

The Global Counters consist of:

Counter

Description

TX Frames

Count of transmitted frames

TX % busy

Percentage of time the tranmitter is not idle

RX frames

Count of received frames

RX % Busy

Percentage of time the receiver is not idle

Eth Errors

Count of Ethernet errors

Eth Type

Type of last error

Protocol Errors

Count of Ethernet protocol errors

Protocol Type

Type of last protocol error

Protocol Slot

Connection number of last protocol error

The global counters cannot be cleared.

Summary of Contents for AN-X2-MOD-MON






























































Search results

Summary of Contents for AN-X2-MOD-MON

Reviews:

Related manuals for AN-X2-MOD-MON

Brands by name

Popular brands

QTS AN-X2-MOD-MON, User Manual

Search results

Summary of Contents for AN-X2-MOD-MON

Reviews:

Related manuals for AN-X2-MOD-MON

Brands by name

Popular brands