-
8
-
-
9
-
qonnect-fasteners.com
UK
DE
NL
FR
ES
IT
RU
PL
SE
UA
Depending on the working mode you choose, the blind rivet nut will be set as follow:
- Manual mode: Press the trigger of the Q-Tool to set the blind rivet nut; the mandrel will
automatically unscrew itself from the set blind rivet nut.
- Automatic mode: The blind rivet nut will be set automatically without any further action.
Immediately after setting the blind rivet nut, the mandrel will unscrew itself automatically
from the set blind rivet nut.
2.2.6 Force reverse button
In case a blind rivet nut is blocked or jammed, the button helps to reverse the mandrel out of
the blind rivet nut. Press corresponding indicator light flashes) and pull the trigger 1 time
to force the mandrel to exit from the blind rivet nut and reset. This action can be applied in several
cases of fault codes as well.
2.3 Troubleshooting
Problem
Possible cause
Solution
Blind rivet nut
is not deformed
enough
- Incorrect stroke (too low)
- The thickness of the workpiece
does not match
- Lithium battery undervoltage
- Increase stroke
- Check blind rivet nuts, and the
plate thickness
- Charge battery or replace with
a charged battery
Automatic blind
rivet nut spin-on
function does not
work
- Size of blind rivet nut does not match
the mandrel size of the Q-Tool
- Mandrel worn out
- Wrong tuning of the protruding
mandrel/anvil
- Change to correct blind rivet
nut, or change to correct mandrel
- Replace the worn out mandrel
- Tune the length of the protruding
mandrel/anvil correctly
The mandrel
is stuck in the
workpiece
- The thread of the blind rivet nut is
damaged or defective
- The mandrel is damaged, or the
wrong size mandrel is used
- Replace the blind rivet nut with
one that is not damaged
- Change the mandrel to one that is
not damaged, and/or to correct size
The mandrel broke
- Stroke too high
- Single side force on the mandrel
- Decrease the stroke settings
The Q-Tool has no
movement
- Empty battery or battery worn
out / damaged
- Riveting capacity beyond Q-Tool
capacity
- Charge the battery, or replace
with a new one
- Select a blind rivet nut tool with
the correct capacity
Fault code
Description
Solution
E1
Communication failure
Remove battery to reset
E2
Power overload
Remove battery to reset
E3
Blind rivet nut jammed / blocked
Press and pull trigger
E4
Stroke failure
Remove battery to reset
E5
Electrical circuit overheated
Let tool cool down (+/-30 min)
E6
Motor overheated
Let tool cool down (+/-30 min)
NOTE:
if the solutions provided above have no effect, the tool must be repaired by qualified
personnel or returned to the dealer or manufacturers’ representative.
3. Battery and Charger
3.1 Technical data
Battery
Weight lithium battery:
0.38 kg
Related voltage:
20V
Capacity:
2.0 Ah
Charger
Charger input voltage:
100-240VAC/50-60 Hz
Charging time:
<60min
Output voltage:
20V
Weight:
0.37 kg
3.2 Battery charging and safety instructions
- Only charge batteries supplied by authorized dealers;
- Always use the original power supply intended for this tool;
- Before charging the battery, please read the warning label of the charger and the battery;
- Do not use a damaged charger for charging;
- Never attempt to charge a damaged battery;
- Never place a dirty or wet battery in the charger;
- Never dispose of batteries with household waste or in fire or water;
- Charger and lithium battery should not be placed in water, exposed to water, snow or any
type of wet environment;
- If the battery spills liquid, avoid contact; if there is any contact, rinse with water and see a
doctor immediately;
- The ambient temperature of charging and discharging is 0
0
C up to max 40
0
C;
- Long term storage of the battery (more than 3 months) must be placed at a temperature of
approx. 23
0
C with a max deviation of 5
0
C.
NOTE:
the battery is not fully charged when it leaves the factory.
In order to ensure the full function of the battery, fully charge it before using. Pay attention to
the charging indicator on the charger. Lithium charging can be charged at any time. Interrup-
tion of charging does not affect its life and will not damage the battery.
The battery is equipped with a temperature detection system.
Remove the battery:
The battery is equipped with a locking mechanism. When the battery is mounted on the
charger, it will be locked into it. If the battery is to be removed, press the unlock button and
slide the battery out of the charger. Do not disassemble.
Failure to comply with these instructions may result in explosions!
UK
DE
NL
FR
ES
IT
RU
PL
SE
UA
