QNAP TS-h 83XU-RP Series User Manual Download Page 43 | Manualshive

Page: 43 / 49

background image

Operation

User Action

Result

Advanced system
reset

Press and hold the
button for 15 seconds.

The default factory settings are restored.

• To retrieve old data after an advanced system reset,

recreate the previous folder structure on the NAS.

LEDs

LEDs indicate the system status and related information when the device is powered on. The following LED
information applies only when the drive is correctly installed and when the device is connected to the
network or to a host.

For details on the location of the LEDs, see

.

TS-hx83XU-RP User Guide

Basic Operations

42

«
...
41
42
43
44
45
...
»

Summary of Contents for TS-h 83XU-RP Series


















































Reviews:

No comments

Related manuals for TS-h 83XU-RP Series

Brand: IBM Pages: 102

Brand: Buffalo Pages: 77

18-51000 Series

Brand: Salsbury Industries Pages: 5

Brand: U-Line Pages: 6

Brand: IBM Pages: 149

Brand: Sako Pages: 19

Brand: G-Technology Pages: 33

Brand: Facom Pages: 2

Mobileraid MR8X

Brand: Sans Digital Pages: 81

Brand: kioxia Pages: 24

Brand: SanDisk Pages: 2

Brand: Hitachi Pages: 208

Brand: Hitachi Pages: 36

Brand: Dot Hill Systems Pages: 134

Brand: Cisco Pages: 23

Brand: Cisco Pages: 75

Brand: Cisco Pages: 132

Brand: Cisco Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands