QHT BIASI B-10 Manual And Installation Download

Page: 1 / 36

Page 1

WHAT TO DO IF YOU SMELL GAS
·

Do not try to light any appliance

· Do not touch any electric switch; do not use any phone in your

building

· Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

If you can not reach your gas supplier call the fire department

Installation and service must be performed by a qualified installer,

service agency or the gas supplier.

Please Read Instructions Carefully

Save for Future Reference

Manufactured by:

Biasi S.p.A.

Verona, Italy

Distributed By:

QHT

QUINCY HYDRONIC TECHNOLOGIES, INC.

80 ROCHESTER AVE. SUITE #12

PORTSMOUTH, NH 03801

PHONE: 603-334-6400

FAX: 603-334-6401

REV. H

If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of
life.

WARNING

DANGER

B10 SERIES BOILER

B3-B9

Boiler Manual And Installation

Instructions for Atmospheric Venting

Summary of Contents for BIASI B-10





































Search results

Summary of Contents for BIASI B-10

Reviews:

Related manuals for BIASI B-10

Brands by name

Popular brands

QHT BIASI B-10, Manual And Installation

Search results

Summary of Contents for BIASI B-10

Reviews:

Related manuals for BIASI B-10

Brands by name

Popular brands