background image

l

Manual 909  

7BI1Bus Interface 

Copyright © 2018 QEI    

 

 

  Introduction  

  11 

Introduction 

1.1  Description 

The 7BI1 Bus Interface card is part of the DLM-6102 and DLM-6103 Distribution Line Modem 
Expansion Kits for the QUICS 3150 Remote Terminal Units. 

The QUICS 3150 Remote Terminal Unit contains a 6CP2 Central Processing card.  When the 
remote is modified with a DLM Distribution Line Modem Expansion Kit, the 6CP2 card is 
replaced with a new 6CPP2 Central Processing Panel. The 6CPP2 panel does not mount into 
the card frame where the 6CP2 was originally installed. The 7BI1 Bus Interface card is 
plugged into the card slot normally occupied by the 6CP2 Central Processing card. The 7BI1 
card is the interface between the I/0 bus of the remote and the newly installed 6CPP2 Central 
Processing Panel. 

The 7BI1 card allows the 6CPP2 Central Processing Panel to become the processing panel. 
Signals that appear on the J4 connector of the 6CPP2 are brought to and from the 
motherboard of the 3150 Remote via the 7BI1. These signals are output onto the 
motherboard in the same fashion as with the 6CP2. Therefore, the cards in the 3150 Remote 
see the 7BI1 as being transparent. That is, they are controlled by the 6CPP2 instead of the 
6CP2. 

Eight (8) option platforms are provided so the 7BI1 can address any eight (8) of the sixteen 
(16) addressable slots of a 3150 Remote card frame. Only eight (8) of the slots can be 
addressed since there are only eight (8) address signals present on the J4 connector of the 
6CPP2. 

Three (3) relays are also provided to select two (2) bus relays and the common transmit relay 
on a 7DPA1 Distribution Power Amplifier. 

1.2  7BI1 Specifications 

Input Power: +12 Volts do @ 50 mA 

External Connections: 

 

P1 - Signals to/from the 3150 Remote motherboard.  

 

J1 - Drives the bus select relays on the 7DPA1.  

 

J2 - Drives optical isolators on Rev B Transceiver board which in turn drives 
bus select relays on 7DPA1. This connector is normally not used. 

 

J3 - Signals to/from J4 connector of 6CPP2. 

NOTE

 

See Table 1-1 for specific signal connections 

 

 

 

 

 

 

 

Summary of Contents for 7BI1














Reviews: