background image

4

 

IS125 Conveyors | Installation & Maintenance Instructions

Installation

 

u

Check Your Shipment

 

Before opening the shipment, visually inspect the outside of the crate/box for shipping damage. Carefully unpack the crate/box, inspecting for component damage which  

 

may have occurred inside the packing materials. Contact the carrier and QC Conveyors regarding any damage that may have occurred during shipment. Check the contents  

 

of your shipment against the supplied packing slip and inform QC Conveyors of any discrepancies.

 

u

General Sequence of Installation 

Mount conveyor to stands 
or compatible mounting 

brackets.

Attach sides or guides to 
conveyor and adjust as 

needed. 

Install drive motor and 
mounting package.

Conveyor should be lagged to 
floor or caster locks engaged 

before operation.

 

u

Assistance

If you need assistance, please contact QC Conveyors customer service department Monday through Friday, 8am-5pm EST at (513) 753-6000. In addition, your local 
distributor has been trained at the factory and can provide support in many ways. You can also visit our website — qcconveyors.com — for additional information and 
technical documents.

Summary of Contents for INDUSTRIAL Series













































Reviews: