background image

12

13

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO-G6.X+ – Q CELLS

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO-G6.X+ – Q CELLS

12

13

Danger! Risk of fatal injury due to electric 
shock! 

 

Ä

Block off the installation zone.

 

Ä

Keep children and unauthorized individuals 
away from the solar power system.

Danger! Risk of fatal injury due to electric 
shock! 

 

Ä

Ensure that modules and tools are not subject 
to moisture or rain at any time during instal-
lation.

Warning! Risk of injury due to falling  
modules! 

 

Ä

Secure modules during installation. 

 

Ä

Do not install modules in windy or wet weather. 

Danger! Risk of fatal injury due to electric 
shock! 

 

Ä

Only use dry, insulated tools. 

 

Ä

Do not carry out the installation alone.

• 

Only install undamaged modules and  
components.

 

Ä

Do not modify the module 
(e.g. do not drill any additional holes).

3  INSTALLATION

3.2  PREPARATION OF INSTALLATION

Option 1:

 

Ä

Fasten the module with 4 clamps  in the 
specified clamping range,  
see Fig. 2, p. 7.

 

Ä

Tighten clamps according to  
manufacturer’s instructions.

 

Ä

Maintain an interval of at least 10 mm between 
two modules along the short side and 5 mm 
along the long side.

10 mm

5 mm

EU

Note! Module damage may occur!

 

Ä

Do not subject modules to mechanical tension. 
Max. torsion 10 mm/m.

Option 2:

 

Ä

Install the module at the 4 mounting points,  
see Fig. 2, p. 7.

 

Ä

Tighten screws according to  
manufacturer’s instructions.

Option 3:

 

Ä

Install the module using mounting profiles,  
see Fig. 2, p. 7.

3  INSTALLATION

3.3 MODULE INSTALLATION

Summary of Contents for Q.PEAK DUO BLK-G6












Reviews: