PVI XR10CX Manual Download Page 13

Page: 13 / 15

Page 13 / 15

PV500-67 03/17

4.2 TYPICAL PARAMETERS FOR ACCESS OVER MODBUS:

Setpoint: Modbus Register 40864

Set

Set point,

This is the typical system setpoint. Read/Write.

Modbus network ID or Address. Modbus Register 40852

Adr

Serial address 0÷247

This is the Modbus address. You should configure this with the keypad.

Temperature of Probe: Modbus Registers 40257

(TP1) Probe 1 temperature

Degrees F (40257)

This is the operating probe that Set references. Read only.

Output Relays (Burner ON): Modbus Coil 543

Statas of Relay, if it is ON the signal for burner is also ON.

Alarms: Modbus Coil 538

Alarms are not typically used on this device.

CONTROL, ON/OFF (Enable/Disable) Modbus Coil 513

ON=257 or 0x0101, OFF=1 or 0x0001
In the OFF state, no heating signal will be present, no alarms, all relay outputs are open, and no temperature are
displayed. The di

splay will show the word “OFF”. It is still possible to read the probe temperatures and other parameters

over Modbus.
This is a write only register. Reading this register will provide invalid results.

5. SERIAL CONFIGURATION

5.1 PORT SETUP

Baud Rate:

9600bps (Not adjustable)

Data Length:

8 bit (Not adjustable)

Parity:

None (Not adjustable)

Stop Bits:

1 (Not adjustable)

Start/Stop:

Silent interval of 3 characters minimum

Minimum Time Between Retry:

500 msec

Summary of Contents for XR10CX
















Search results

Summary of Contents for XR10CX

Reviews:

Related manuals for XR10CX

Brands by name

Popular brands

PVI XR10CX, Manual

Search results

Summary of Contents for XR10CX

Reviews:

Related manuals for XR10CX

Brands by name

Popular brands