manualshive.com logo in svg

PVI Industries TEMPTRAC, Manual, Page: 17 / 30

Share
Download
PVI Industries TEMPTRAC Manual Download Page 17

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST 

Page 17 of 30 

PV7069-T   03/17 
Part number 129209 

TYPICAL POINTS: 

Probe 2 

Read Only 

Probe 2 in degrees F 

MODBUS 

Holding Register 

258 

40259 

BACNET 

Probe2 

25900 

Deg-F 

LONWORKS 

nvoProbe2_# 

 

Deg_F 

Optional probe on some devices, usually installed on most devices. If installed and enabled, returns the 
temperature of the probe in degrees F. Connection on TempTrac is green screw terminals 15 and common 17. 
 

Probe 3 

Read Only 

Probe 3 in degrees F 

MODBUS 

Holding Register 

260 

40261 

BACNET 

Probe3 

26100 

Deg-F 

LONWORKS 

nvoProbe3_# 

 

Deg_F 

Optional probe on some devices, not usually installed on most devices. If installed and enabled, returns the 
temperature of the probe in degrees F. Connection on TempTrac is green screw terminals 16 and common 17. 
 

Burner Runtime 

Read/Write 

Burner Runtime Hours 0-65535  

MODBUS 

Holding Register 

848 

40849 

BACNET 

BURNER_HOURS_ou1 

84900 

Hours 

LONWORKS 

nvoBrnHr_ou1_ # 

nviBrnHr_ou1_# 

Hours 

NOTE: Number of hours the burner has been enabled. Once it reaches 9999. This can be written to, as a way 
to reset it. 
 

Modulation Rate 

Read Only 

Monitor the modulation signal 

MODBUS 

Holding Register 

262 

40263 

BACNET 

Modulation_FR 

26300 

 

LONWORKS 

nvoMod_FR_# 

 

 

Modulation rate on the analog output 4-20ma is represented as 0-100. This feature was introduced in Firmware 
0.5 (5) and is not available from older TempTrac modules already in the field. 
 

Burner_Relay1 

Read Only 

Status of burner, Relay1 (Output 1) 

MODBUS 

Holding Register 

2049 

42050:0 

BACNET 

Burner_Relay1 

205050 

 

LONWORKS 

nvoBrn_Rel1_# 

 

 

This is Bit 0 of the Relay status word. It is the relay that controls the main heating output. Typically the Burner 
Status. BACNET and LONWORKS have this broke out into state logic points. MODBUS, you will have to break 
it out yourself. Read value, BITWISE AND with 0x0001, if result = 0, relay is off. If result = 1, relay is on. 
 

Alarm_AL2 

Read Only 

Status of digital input #2 Alarm 

MODBUS 

Holding Register 

3328 

43329:11 

BACNET 

Alarm_AL2 

332961 

 

LONWORKS 

nvoAlarm_AL2_# 

 

 

Digital Input #2 alarm. On some products, this is a general failure to operate alarm. See product specific 
information. This is Bit 11 of the ALARM STATUS ALL word. 

Flashes ‘AL2’ or ‘LP’ on TempTrac display. In 

BACNET and LONWORKS, this is broken out into a state logic point. 
For MODBUS ALARMS && 0x0800 = 0x0800 Alarm is active. = 0x0000 Alarm is not active. 
 

Summary of Contents for TEMPTRAC































Reviews:

No comments