background image

Plumbing System

5-1

Section 5

DC235 / DC265

Plumbing System

5.1 Fresh Water System

General 

The fresh water system consists of a potable
water tank, distribution lines and a distribu-
tion pump. The pump is equipped with an
automatic pressure switch and is located  in
the  forward storage compartment. An in-line
strainer located near the pump protects the
system from debris. The tank is filled
through a labeled deck fill located under the
baitwell hatch. 

DO NOT confuse other deck fill with fresh
water fill. If toxic fluids or fuel is added to
fresh water tank, the system will be contami-
nated. DO NOT attempt to pump fuel out;
this system is not designed to pump fuel.
Fuel must be removed by qualified person-
nel only. Fuel in the fresh water systems will
also require replacement of that system and/
or many components.

 

Operation

Fill the water supply tank slowly through the
FRESH WATER FILL deck plate. After filling
tank, partially open all faucets. Turn on
“Fresh Water System” switch at the helm.
Allow the pump to run until all of the air is
purged from the system and a steady stream
of water is flowing from each outlet. Next,
turn off the faucets one by one. As the pres-
sure builds, the pump will automatically shut
off.

When properly primed and activated, the
water system will operate like the water sys-
tem in a home. An automatic pressure sen-
sor keeps the system pressurized. If the
system has been recently filled or has not
been used for an extended period, air may
accumulate at the pump and the system
may have to be re-primed.

Whenever the boat is left unattended, turn
the fresh water system switch "OFF." 

5.2 Raw Water Washdown

DC 235

The raw water wash down fitting is supplied
raw water by the livewell pump.

Operation

To use the raw water washdown, turn on the
livewell, close the diverter valve that is part
of the livewell inlet. Raw water will be
directed to the fitting. As pressure builds in
the washdown hose the pressure switch on
the livewell pump will open causing the
pump to turn off. When the washdown hose
is in use, the pressure will drop and the
pump will turn on. Open the livewell diverter
valve when the washdown hose is not in use
or turn off the livewell pump if the livewell in
not in use.

!

DANGER

FIRE OR EXPLOSION HAZARD

Fuel and their vapors are highly explo-
sive when exposed to open flame or
spark, resulting in death or serious
injury. Do not confuse deck fills.

!

CAUTION

DO NOT allow the fresh water pump to
run dry; damage to the pump can
occur. The fresh water pump works on
demand and WILL NOT shut off when
the tank is empty. Turn the water
pump switch "OFF" when the system
is not in use. Operating any pump
from a low-charged battery can lead to
a pump failure. Keep the batteries
properly charged. The fresh water
system must be properly winterized
prior to winter lay-up. Refer to Winter-
izing.

Summary of Contents for DC / 265



























































































































Reviews: