background image

20

LIMITED COMMERCIAL WARRANTY POLICY

Purkeys Fleet Electric, Inc. (hereafter “Purkeys”), warrants each product to be free of defects 

in material or workmanship under normal use and service. This warranty is for the benefit of 

Original Equipment Manufacturers, Dealers, Warehouse Distributors, Fleets, or other End 

Users (hereafter “Customers”) and covers products manufactured by Purkeys and sold new to 

Customers either directly by Purkeys or by its authorized dealers, distributors, or agents. The 

length of the Warranty Period is 36 months.
The warranty period commences on the in-service or install date and is not transferable. 

Failure to provide the in-service or install date on the warranty claim form will cause the 

warranty period to begin on the date the part was manufactured or date of sale recorded on the 

original sales invoice, whichever is earlier.
A completed warranty claim form should accompany all parts submitted to Purkeys for 

consideration for repair or replacement under warranty. The submitted claim form should 

contain all of the information required. Lack of a properly or fully completed claim form will 

result in delay or denial of warranty claim. Claims must be submitted no later than 30 days 

after part is removed.
This warranty does not apply if, in sole judgement of Purkeys, the product has been damaged 

or subjected to accident, faulty repair, improper adjustment, improper installation or wiring, 

neglect, misuse, or alteration or if the product failure is caused by defects in peripheral vehicle 

components or components attached to the Product or failure of a part not manufactured by 

Purkeys.
This warranty shall not apply if any Purkeys product is used for a purpose for which it is not 

designed or is in any way altered without the specific prior written consent of Purkeys. ANY 

Product alleged by a Customer to be defective must be inspected by Purkeys as a part of the 

warranty claims process in order to confirm that the part has failed as a result of a defect in 

material or workmanship.  
Transportation for products and parts submitted to Purkeys for warranty consideration must 

be prepaid by Customer. Repaired or replaced products and or components will be returned to 

Customer pre-paid by Customer or “freight collect” to the address provided by Customer in the 

warranty claim form. No charge will be made for labor or material in effecting such repairs.
The Warranty provided by Purkeys hereunder is specifically limited to repair or replacement 

of the Product as Purkeys deems most appropriate in its sole discretion. Purkeys neither 

assumes nor authorizes any other person to assume on its behalf any other warranty or 

liabilities in connection with Purkeys products. The Warranty does not apply to fuses or other 

“consumable” or maintenance items which are or may be a part of any Purkeys product.
THIS WARRANTY DOES NOT APPLY TO LOSS OF VEHICLE OR EQUIPMENT, LOSS OF 

TIME, INCONVENIENCE, OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. 

PURKEYS SPECIFICALLY DISCLAIMS AND SHALL NOT BE LIABLE FOR INCIDENTAL 

OR CONSEQUENTIAL DAMAGES arising out of or from the use of Purkeys products by the 

Customer. 
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, INCLUDING 

COMMON LAW WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE, 

MERCHANTABILITY, AND ANY OTHER EXPRESS OR IMPLIED WARRANTIES. ALL 

OTHER SUCH WARRANTIES ARE SPECIFICALLY DISCLAIMED.
This Limited Commercial Warranty supersedes all previous Warranty Policies issued by 

Purkeys and any of its suppliers.

Summary of Contents for SOLAR BOLT

























Reviews: