Purkeys SOLAR BOLT Installation Manual Download | Manualshive

Page: 11 / 24

background image

9

P: 479.419.4800 | F: 479.419.4801 | www.purkeys.net

SOLAR BOLT INSTALLATION GUIDE

Step 1: Route main harness back

toward the liftgate batteries.

Secure with wire ties or cable

clamps as you go.

Step 2: Once the cable is routed to

the battery box, feed the Solar Bolt

main harness into the battery box

through a dome nut or a grommet.

DO NOT cut the harness until the

mounting location for the Solar

Bolt controller is determined.

CABLE ROUTING

Installation Complete

Important: Place the supplied cable clamps along the 2-conductor jacketed

cable every 18 inches to ensure proper support for the cable. Avoid sharp

edges and possible chaffing points.

«
...
9
10
11
12
13
...
»

Summary of Contents for SOLAR BOLT

























Reviews:

No comments

Related manuals for SOLAR BOLT

Brand: B&PLUS Pages: 30

Brand: B&PLUS Pages: 24

Brand: Sennheiser Pages: 28

PARAPROJECT CUBE U10

Brand: Parat Pages: 6

Brand: Base Pages: 2

Brand: T&D Pages: 2

Brand: Fubag Pages: 14

Brand: Alpina Pages: 164

Brand: Harbor Freight Tools Pages: 14

PowerLuber C Series

Brand: Lincoln Pages: 2

EVERVOLT EV-BMS

Brand: Panasonic Pages: 30

CK1 Serial Dock

Brand: Intermec Pages: 147

Brand: EverStart Pages: 9

CB1224xA SERIES

Brand: ADELSYSTEM Pages: 2

Brand: Chauvet DJ Pages: 28

Brand: Green motion Pages: 23

Brand: Magnum Dimensions Pages: 58

Brand: Targus Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands