PureTools PT-HDBT-701-TXWP User Manual Download Page 18

Page: 18 / 28

User Manual

PT-HDBT-701-TXWP

5.3

RS232 Command

Communication protocol:

RS232 Communication Protocol

Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none

5.3.1

Control Mode Switching

Command

Function

Feedback Example

50779%

Switch to RS232 mode 1

（

Default

）

control scaler switcher and the far-end
third-party device.

RS232 Mode 1: RS232
Control Scaler & Remote.

50780%

Switch to RS232 mode 2, control the
scaler switcher from remote.

RS232 Mode 2:RS232 &
Remote Control Scaler

5.3.2

Signal Switching

Command

Function

Feedback Example

50770%

Enable auto-switching

Auto Switching

50771%

Disable auto-switching

Manual Switching

50702%

Switch to HDMI input

Switch to HDMI

50704%

Switch to VGA input

Switch to VGA

5.3.3

VGA Scaling Configuration

The default output resolution for VGA is 1920x1080. Below is a list of the output
resolutions the built-in scaler can output.

Command

Function

Feedback Example

50632%

Check the output resolution

Resolution: xx

50619%

Change the resolution to 1360X768
HD

Resolution: 1360x768

50626%

Change the resolution to 1024X768
XGA

Resolution: 1024x768

Summary of Contents for PT-HDBT-701-TXWP




























Search results

Summary of Contents for PT-HDBT-701-TXWP

Reviews:

Related manuals for PT-HDBT-701-TXWP

Brands by name

Popular brands

PureTools PT-HDBT-701-TXWP, User Manual

Search results

Summary of Contents for PT-HDBT-701-TXWP

Reviews:

Related manuals for PT-HDBT-701-TXWP

Brands by name

Popular brands