background image

Index

Installation Guide

Update Alert

: Firmware updates are posted to the web on a regular basis. We recommend 

that you check for firmware and/or install guide updates prior to installing this product.

SmartStart Compatible

SmartStart is equipped with D2D, which means it can be connected to an interface module and used in Range 
Extender Ready (RXT) mode without the use of a remote starter. See the 

Module Programming 

section for more 

information.

© 2016 Directed. All rights reserved.

Rev.: 20160810

Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation

Vehicle Application Guide................................................................................................................................................

Installation

Installation (Wiring Diagram & Vehicle Wiring Reference Chart).....................................................................................
SmartStart/XL202 Installation Notes...............................................................................................................................

Programming

Module Programming......................................................................................................................................................
Module Reset & Hard Reset............................................................................................................................................
Feature & Option List.......................................................................................................................................................
Feature Programming......................................................................................................................................................

LED Diagnostics & Troubleshooting................................................................................................................................

Limited One-Year Consumer Warranty............................................................................................................................

Quick Reference Guide...................................................................................................................................................

02

03
05

06
07
08
08

09

12

13

®

 Ford and Lincoln are registered trademarks and property of their respective companies.

This guide supports the installation of a DBALL in 

Range Extender Ready

 (R

XT

)

 mode. This solution 

offers two (2) configuration options to control your system: Optional RF Kits or SmartStart (both sold 
separately).

Important!

This product is ONLY compatible with vehicles equipped with a factory-installed remote starter.

Range Extender Ready (RXT) is used to dramatically increase the factory remote start activation range 
compared to the factory transmitter. Refer to the 

Quick Reference Guide 

for more information.

Summary of Contents for DBALL














Reviews: