Xpresskit DBALL Installation Manual Download Page 10

© 2016 Directed. All rights reserved.

Rev.: 20160810

Platform: DBALL/DBALL2
Firmware: FORD3 Range Extender Ready (RXT) Installation

LED

Description

Troubleshooting

OBDII feature is not supported.

The diagnostic data bus was not detected, therefore the 
SmartStart features will be limited.

Ground When Running (Status) command received.

The module has initialized the remote start sequence.

Ignition ON command received.

The module has received the Ignition ON command and is 
processing the remote start sequence.

Start ON command received.

The module has received the Start ON command and is 
processing the remote start sequence.

PTS shutdown error.

The PTS output from the module was not activated due to 
safety protection.

CAN bus incorrectly detected.

Verify the CAN1 and CAN2 connections. Refer to “Installation 
(wiring diagrams & vehicle wiring reference charts)” to check 
the connections.

LOCK command received.

UNLOCK command received.

TRUNK command received.

AUX1 command received.

AUX2 command received.

AUX3 command received.

Takeover successful.

Normal operation.

Runsafe was not disabled.

No UNLOCK command was received prior to opening the 
door, or the 45 second timer expired in takeover mode.

Brake was not detected.

The brakes were not detected, which prevents the system 
from shutting down the vehicle.

Smart key was not detected.

The smart key was not detected, which prevents the system 
from shutting down the vehicle.

Speed was detected.

The vehicle was detected as moving, which prevents the 
system from shutting it down.

External module synchronization

Commands

Activation Ground When Running (Status)

If the bypass module fails to flash, it did not receive the 
signal. Commands can come from RF or D2D.

Shutdown codes

(Flashes red,
red then
orange) x 10

Flashes red
& orange

Flashes red
x 21

Flashes red
x 2

Flashes red
x 4

Flashes red
x 10

Flashes red
x 1

Flashes red
x 3

Flashes
green

Flashes
green
quickly

Flashes
green x 1

Flashes
orange x 1

Flashes
orange x 2

Flashes
orange x 3

Flashes
orange x 5

Flashes
orange x 4

Flashes
orange x 6

Page 10

Summary of Contents for DBALL














Reviews: