background image

MODEL#9335MSS

13

FREQUENTLY ASKED QUESTIONS

Question: “How should I clean my 

swings and 

seesaw?”

Answer: you should clean the 

product 

with a solution of warm 

water and Non- Corrosive/Abrasive 

soap. Dampen a rag with this 

solution and wipe completely dry 

before using.

Question: “A seat seems loose, 

what should I do?”
Answer: Make sure the Bolts/Nuts 

under the plastic seat are secure.

CARE & MAINTENANCE

Before each use of this product, inspect the entire assembly

and replace any worn, defective or missing parts.

The following conditions could represent potential hazards:

Missing, improperly positioned, or insecurely attached 

seats

;

A

 

bent or broken

 

frame; 

Cracked or broken seats. 

Cease

using

 

seesaw 

immediately and secure it against

 

unauthorized

use if

 

any of these conditions are present.

Regularly check to see if the steel tubes, seats, backrests and

other parts are tightened and completely secure. Replace

worn

 

& damaged parts if found and if necessary, secure from

use

 

until replacement parts can be obtained.

If the paint is chipped, we recommend you lightly rub the

damaged area and cover using a non-toxic enamel paint.

High touch surfaces made of plastic or metal, such as grab

bars and railings should be cleaned routinely.

Do NOT use bleach as it may cause colors to fade.

Use wet towel or cloth with mild soap and water solution to

wipe down metal parts, seats and handlebar. Dry

Immediately and do not 

allow children to 

use until

completely dry.

To disinfect surfaces - use a 70% / 30% Rubbing Alcohol

to Water mix to clean seat and handlebar surfaces. The

surface must remain visibly wet for at least 4 minutes,

allowing it to dry on its own. After 4 minutes, the surface

may be rinsed thoroughly and wiped dry to eliminate water

marks. This solution will lose its effectiveness in about 24

hours, so a new batch must be made each day.

Question: “Something was missing 

from the packaging,” “I need to 

purchase a replacement part” or “I 

discovered a damaged piece. What 

should I do?”
Answer: Contact customer service. 

You must have proof of purchase 

and/or order confirmation available to 

be considered for warranty 

replacement. You must report 

missing pieces within 30 days of 

purchase.

Thank You Coupon!

As a way of saying thank you for purchasing one of our products, here is a 10% OFF coupon for 

your next purchase at 

www.PureFun.net

Use Code: GQBRANDS10 at Checkout

Cleaning your Playground Equipment

Summary of Contents for 9335MSS














Reviews: