PulseTec Ultima 250 Duo Instruction Manual Download Page 31

Page: 31 / 40

ITEM

SELECTION

DESCRIPTION

NiMH

Sensitivity

D.Peak

Default

Default: 4mV/Cell

5 -15mV/Cell

This setting is for NiMH/NiCd battery only.

When the charger detects that the delta peak

value you set has been reached, the charger

will say the battery is fully charged.

NiCd

Sensitivity

D.Peak

Default

Key Beep ON
Buzzer ON

OFF/ON

Key Beep sounds every time you press a

button. Buzzer beep or melody sounds at

various instances during operation to alert

certain process events.

DC Input. Low
Cut-Off 11.0V

10.0-11.0V

This setting controls the DC input voltage.

If the voltage drops below the value you set

the charging operation will be terminated to

protect the input channel.

OFF

Synchronization

OFF/ON

If you set it , channel 2 will synchronize the

same operation as Channel 1.

Load Factory Set
Enter

Press ENTER to load factory default setting.

HW: 1.00

FW: 1.10

Load Factory Set

It indicates the hardware and firmware

version.

System Setting

Summary of Contents for Ultima 250 Duo









































Search results

Summary of Contents for Ultima 250 Duo

Reviews:

Related manuals for Ultima 250 Duo

Brands by name

Popular brands

PulseTec Ultima 250 Duo, Instruction Manual

Search results

Summary of Contents for Ultima 250 Duo

Reviews:

Related manuals for Ultima 250 Duo

Brands by name

Popular brands