Pulsar PSUPS10A12 Manual Download Page 11

www.pulsar.pl 

 

 

 

 

PSUPS10A12 

 

 

 

 

 
 

11 

 

 

WEEE MARK 

 
According to the EU WEE Directive 

– It is required not to dispose of electric or electronic waste as 

unsorted municipal waste and to collect such WEEE separately. 

 
 

 

CAUTION! 

The power supply unit is adapted for a sealed lead-acid battery (SLA). After the operation period it must not be disposed of but 

recycled according to the applicable law.

 

 

 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

GENERAL WARRANTY CONDITIONS 

 

1. Pulsar (the manufacturer) grants a five-years warranty for the equipment, counted from the device’s production date. 
2.  The warranty includes free-of-charge repair or replacement with an appropriate equivalent (the selection is at the 

manufacturer’s discretion) if the malfunction is due to the manufacturer, includes manufacturing or material defects, unless such 
defects have been reported within the warranty period (item 1).  

3. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main office of the 
manufacturer.  

4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the defect.   
5. Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenienve, however 

not later that within 14 days from the delivery to the service centre of the manufacturer.  
6. The repair period mentioned in item 5 may be prolonged, if there are no technical possibilities to carry out the repairs, or if the 

equipment has been conditionally accepted, due to the breaking warranty terms by the claimant.  
7. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer, exclusively.  

8. The warranty does not cover the defects of the equipment, resulting from: 

- reasons beyond the manufacturer's control, 
- mechanical damage, 

- improper storage and transport, 
- use that violates the operation manual or equipment’s intended use 

- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,  
- improper installation and configuration (in defiance with the manual), 

9. The warranty is void in any of the following circumstances: 
- construction changes  

 

- repairs carried out by any unauthorized service center 
- damage or removal of warranty labels 

- modifications of the serial number 
10. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined according to the 

wholesale prices suggested by the manufacturer on the day of purchase.  
11. The manufacturer takes no reponsibility for the defects that result from:  

- the damaging, malfunctioning or inability to operate the equipment 

- defects that result from using the equipment outside its stated specifications and operating parameters failing to abide by the 
recommendations and requirements contained in the manual, or the use of the equipment.  

 

Summary of Contents for PSUPS10A12













Reviews: