Pulsafeeder Pulsalube 8 GS Ultra, Operation & Maintenance Manual

Page: 188 / 198

90.1 HELICAL-BEVEL FLANGED
OIL FILL QUANTITIES
RETAIN FOR FUTURE USE
U12100 - 1 of 1
Type M1 M2 M3 M4 M5 M6
Quarts Liters Quarts Liters Quarts Liters Quarts Liters Quarts Liters Quarts Liters
SK 9012.1 1.06 1.00 2.01 1.90 2.01 1.90 2.32 2.20 1.27 1.20 1.80 1.70
SK 9013.1 1.53 1.45 2.43 2.30 2.22 2.10 2.96 2.80 1.11 1.05 1.90 1.80
SK 9016.1 1.06 1.00 2.01 1.90 2.01 1.90 2.32 2.20 1.27 1.20 1.80 1.70
SK 9017.1 1.53 1.45 2.43 2.30 2.22 2.10 2.96 2.80 1.11 1.05 1.90 1.80
SK 9022.1 1.69 1.60 3.70 3.50 3.70 3.50 4.44 4.20 2.43 2.30 2.96 2.80
SK 9023.1 2.43 2.30 3.70 3.50 4.02 3.80 5.60 5.30 2.32 2.20 3.59 3.40
SK 9032.1 2.22 2.10 5.07 4.80 6.76 6.40 7.50 7.10 3.49 3.30 5.39 5.10
SK 9033.1 3.91 3.70 6.02 5.70 7.08 6.70 9.09 8.60 3.80 3.60 5.60 5.30
SK 9042.1 4.76 4.50 10.6 10.0 10.6 10.0 12.2 11.5 6.87 6.50 8.66 8.20
SK 9043.1 6.87 6.50 11.1 10.5 12.6 11.9 15.5 14.7 7.08 6.70 9.83 9.30
SK 9052.1 7.93 7.50 17.4 16.5 21.1 20.0 24.8 23.5 12.2 11.5 19.0 18.0
SK 9053.1 13.7 13.0 19.0 18.0 22.7 21.5 28.0 26.5 13.7 13.0 18.0 17.0
SK 9062.1 12.7 12.0 29.1 27.5 34.9 33.0 40.7 38.5 20.1 19.0 27.5 26.0
SK 9072.1 12.7 12.0 29.1 27.5 34.9 33.0 40.7 38.5 20.1 19.0 27.5 26.0
SK 9082.1 22.2 21.0 57.0 54.0 70.0 66.0 85.0 80.0 40.2 38.0 55.0 52.0
SK 9086.1 38.0 36.0 82.0 78.0 96.0 91.0 113 107 56.0 53.0 80.0 76.0
SK 9092.1 42.3 40.0 137 130 163 154 185 175 87.0 82.0 96.0 91.0
SK 9096.1 85.0 80.0 198 187 204 193 272 257 119 113 165 156
Oil Levels shown apply to base models and gear units ending in AZ, AF, VZ, & VF.
www.nord.com/docs 12.22.14
NORD Gear Corporation
Toll Free in the United States: 888.314.6673
NORD Gear Limited
Toll Free in Canada: 800.668.4378
M6
M2
M3
M5
M4
M1
90.1 Helical-bevel flanged lubrication
Unless otherwise noted below, the following NORD Gear
reducers are shipped from the factory with a pre-determined
oil fill level in accordance to the specified reducer size and
mounting position. For additional information, please refer
to the “Oil Plug & Vent Locations” documentation for your
gear unit.
STOP
HARMFUL SITUATION
STOP
Actual oil volume can vary slightly depending upon the
gear case size, mounting and ratio. Prior to commission-
ing the reducer, check the oil-fill level using the reducer’s
oil level plug and drain or add addition oil as needed. The
minimum acceptable oil level is 0.15 in (4mm) below the
oil level hole.
For mounting orientations other than shown please consult
NORD Gear. Reducer modifications may be required.
VF Unit Shown