Puls FIEPOS FPS300 Manual Download

Page: 3 / 28

FPS300.245-049-102

All parameters are specified at 24 V, 12.5 A, 230 Vac, 25 °C ambient and after a 5 minutes run-in time unless otherwise noted.

Apr. 2022 / Rev. 0.2 FPS300-EN

www.pulspower.com

3 / 28

OMENCLATURE

Detail

Description

FPT

380-480 V 3 Phase IP54-67 Power Supply

FPS

100-240 V 1 Phase IP54-67 Power Supply

FPH

200-240 V 1 Phase IP54-67 Power Supply Highline Input Voltage

300

300 W Power Class

500

500 W Power Class

241 / 481

Standard Power Supply with Output Voltage 24-28 V / 48-52 V Setting and LED Bar

242 / 482

Basic Power Supply without Voltage Setting and LED-Bar. This version has a status LED Bar.

245 / 485

Power Supply with up to 4 E-Fuse Channels

246 / 486

Power Supply with up to 4 NEC Class II Channels

247 / 487

Power Supply with NEC Class II and E-Fuse Channel

0xx

Terminal configuration e.g. .002. Input: HanQ4/2 Com: M12-A Output: HanQ4/0

1xx

Consecutively numbered

Summary of Contents for FIEPOS FPS300





























Search results

Summary of Contents for FIEPOS FPS300

Reviews:

Related manuals for FIEPOS FPS300

Brands by name

Popular brands

Puls FIEPOS FPS300, Manual

Search results

Summary of Contents for FIEPOS FPS300

Reviews:

Related manuals for FIEPOS FPS300

Brands by name

Popular brands