background image

psmailers.com  •  800.464.5030 

PS

M

ailers

  

PSM10K

5

Operator Safety

• 

Please review and follow all the safety precautions to 
ensure safe equipment operation.

 The user is responsible for 

safe operating conditions. Read all operating instructions prior 
to operating machine.

 

Warning:

 Do not attempt to handle the equipment alone. It 

requires two people to handle and lift the equipment out of  
the packaging.

 

Warning:

 This unit contains moving parts. Watch for 

Caution

Warning

, and 

Electrical

 stickers detailing proper operating 

conditions and user safety.

•  Never remove guards

 or 

product safety switches.

 Removal of 

guards or switches will cause the unit to run improperly and  
can result in personal injury.

•  Keep all hands, fingers and objects away from moving parts. 

Never attempt to reach into the machine while the power is  
on. Turn off the machine and disconnect the power cord before 
cleaning or servicing the machine, and before removing either 
fold plate. Injury may occur if proper operating procedure is  
not followed.

•  Plug the power cord into 115 VAC, 60 Hz outlet only. 

Voltage  

up to 120 V will not damage the machine.

•  The power cord and plug must be accessible at all times for 

disconnection.

•  This unit is equipped with a 3-wire, grounded electrical cord. 

 

If the cord becomes damaged and needs to be replaced, it 
must be replaced with an authorized part available through  
the manufacturer or an authorized service agent.

•  All machine maintenance should be performed only by factory 

authorized service personnel using factory authorized replace-
ment parts. Contact your sales rep for more information.

•  Keep the 

PSM10K

 away from extreme heat and moisture.

•  Never operate the 

PSM10K

 while tired, drowsy, or under  

the influence of medication, drugs, or alcohol. Failure to do  
so can result in personal injury.

•  Never operate the 

PSM10K

 with loose clothing or jewelry. 

Contain all long hair and neck ties prior to operating machine. 
Failure to do so could result in clothing, jewelry, or hair 
becoming entangled in moving parts.

Summary of Contents for PSM10K

























Reviews: