background image

 

Type key 

Example 

 

PSF-402-SE-EX 

 

 24VAC 

50-60Hz 

9W 

2,0kN 

0,33 

 

 

  

 

 

  

 

 

  

 

 

  

 

 

  

  

  

 

 

 

 

 

  

 

 

  

 

 

  

 

 

  

 

 

  

  

  

 

 

 

Actuator type 

 

 

  

 

 

  

 

 

  

 

 

  

  

  

 

 

 

Spring retract / valve stem is 
extending 
Spring extend / valve stem is 
retracting 

     

 

 

  

 

 

  

 

 

  

  

  

 

 

 

Voltage supply 

     

  

     

 

 

  

 

 

  

  

 

  

 

 

  

 

Frequency 

  

  

     

  

     

  

     

 

 

  

  

  

 

 

 

Max. input power 

  

  

  

     

  

     

  

     

  

  

 

 

 

Force 

  

  

     

  

     

  

     

  

     

  

  

 

 

 

Stroking speed [mm/s] 

     

  

     

  

     

  

     

  

  

  

  

 

1. Symbols and safety 

General dangers of non-compliance with safety regulations 

PSF-Ex actuators are built at state-of the art technology and are safe to operate. Despite of this, the actuators may 
be hazardous if operated by personnel that has not been sufficiently trained or minimum instructed, and if the 
actuators are handled improperly, or not used as per specification. 
 
This may 

 

cause danger to life and limb of the user or a third party,  

 

damage the actuator and other property belonging to the owner, 

 

reduce safety and function of the actuator. 

 
To prevent such problems, please ensure that these operating instructions and this chapter in particular have been 
read and understood by all personnel involved in the installation, commissioning, operation, maintenance and repair 
of the actuators. 
 

Basic safety notes 

 

The actuators may only be operated by skilled and authorized operating personnel. 

 

Make sure to follow all security advices mentioned in this manual, any national rules for accident prevention, as 
well as the owner´s instructions for work, operation and safety. 

 

The isolating procedures specified in these operating instructions must be followed for all work pertaining to the 
installation, commissioning, operation, change of operating conditions and modes, maintenance, inspection, 
repair and installation of accessories. 

 

Areas that can be under voltage have to be isolated before working on them. 

 

When installing the actuators, observe IEC/EN60079-14. 

 

Ensure that the actuators are always operated in faultless condition. Any damage or faults, and changes in the 
operational characteristics that may affect safety, must be reported at once. 

 

Danger signs  

The following danger signs are used in this operating manual: 

 

Caution!

 There is a general risk of damage related to health and/or properties. 

Summary of Contents for PSF-M-EX



















Reviews: