background image

 

18 

Note 
Automatic commissioning can be started via software PSCS -> See relevant operation manuals 
 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 

 
11.2 Manual Commissioning 

If both cut-offs are selected to be „by position“, the actuator must be commissioned manually using the software 
PSCS or the control box PSC.  
 
Mount the actuator to a valve, wire it and switch the power on, according to these instructions. Permanently apply 
the set-value for the closed position, or the input signal „close“.  

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Drive the actuator to the closed position of the valve using software PSCS or control box PSC. The open position of 
the valve will be calculated in accordance with the programmed valve stroke. 
 
After manual commissioning, the actuator is ready for use. The green LED is glowing permanently.  
 
Note 
If the parameterised valve stroke, starting from the adjusted closed position, exceeds the possible actuator stroke, 
then the operating stroke will be reduced to the resulting maximum possible value. 
 
 
 
 
 

Caution! 
If the LEDs display other types of signals than 
“flashing green” or “glowing green permanently”, 
please refer to the chapter 15 on “Tracing Faults”. 
 
 
 
Caution! 
The mains supply must not be interrupted during 
the commissioning run! 
 

Caution! The actuator operates the valve! 

Caution! 
The valve stroke has to be parameterised using 
software PSCS or control box PSC! -> See relevant 
manuals. 

Summary of Contents for PS-AMS PSQ Series

























Reviews: