manualshive.com logo in svg

Protrol IPS2 24 VDC, Manual, Page: 23 / 25

Share
Download
Protrol IPS2 24 VDC Manual Download Page 23

 

Ver 1710 Rev 1

 

Protrol AB

 

 

Tel: 031- 45 82 00

 

Ullevigatan 19 

 

internet: www.protrol.se  

411 40 Göteborg 

23

 

e-mail: [email protected]

 

7  Testing and Commissioning of IPS2 

Before taking an IPS unit into operation it can be tested either in off site or installed in the station. It can be 
tested with a single current source for both overcurrent and earth fault functions. 

7.1  Binary I/O 

Test of Binary Inputs 

Apply a test voltage to the binary inputs and verify that the IPS2 unit detects the signals and transmits them 
to the dispatch centre. 

7.2  Current Injection Test 

Test circuit 

Connect the current source to phases A and B (or any other combination of two phases) according to Figure 
11. Apply a current of 0.5 A. The measured sum of the phases shall now be zero. Verify with the built-in 
transient fault recorder of Protrol Tool. See section below for details. 

 

 

Figure 11. 

Current injection test. 

Overcurrent Test 

Increase the current of the current source until overcurrent is detected. This is indicated by the OC LED and 
the output relay will close for the set time, if applicable. Note: If an input is used to release the output 
signal this input must be set high. 

Verify that the OC Start and Trip signals are transferred to the dispatch center. 

IPS

 

 
 
 
 

 

Current

 

Source

 

1 A

 

Summary of Contents for IPS2 24 VDC


























Reviews:

No comments