manualshive.com logo in svg

Protrol IPS2 24 VDC, Manual, Page: 20 / 25

Share
Download
Protrol IPS2 24 VDC Manual Download Page 20

 

Ver 1710 Rev 1

 

Protrol AB

 

 

Tel: 031- 45 82 00

 

Ullevigatan 19 

 

internet: www.protrol.se  

411 40 Göteborg 

20

 

e-mail: [email protected]

 

IEC 60870-5-101 Object Settings 

 

 

 

 

Time Tag 

0..1 

 

0 

0

: No time tag included 

1

: Time tag included 

Address [8] 

1..255 

 

0 

The highest address octet 

Address [16] 

0.. 65534 

 

1 to 9 

The two lowest address octets 

Analogue type 

0..3 

 

1 

0

: 

Raw, 

rated current 3800 units 

1

: 

Normalized 

to the nominal CT ratio 

2

: 

Scaled

 to integer primary current in Amperes. 

3

: 

Float

ing point primary current in Amperes 

Deadband 

1..50 

% 

10 

Deadband for the update of analogue objects in percent of 
rated current (

CT ratio

) 

Remark: The deadband for I

0

 is half of the I

0

 setting. If the I

0

 

stage is disabled, the deadband is 2.5 A 

 

 

Factory Defaults 

It is possible to reset all settings in the configuration tool to factory defaults by pressing the 

Factory

 button. 

Open Configuration File 

Previously saved settings can be reloaded to the configuration tool by pressing the 

Open

 button. A dialog 

opens and it is possible to browse and choose the desired configuration file. Press 

Open

 to read the file. 

Edit Configuration Data 

After the 

Factory

 or 

Open

 buttons have been pressed it is possible to adjust configuration data. 

 

Save Configuration File 

The current settings can be save by pressing the 

Save

 button. A dialog opens and it is possible to adjust the 

file name before 

Save

 is pressed a second time. 

Clear Display 

It is possible to clear all settings in the configuration tool by pressing the 

Clear Display

 button. 

Download Configuration File 

The current configuration file can be downloaded to a connected IPS2 unit by pressing the 

Download…

 

button. Please see the chapter “

Download a Configuration File to the IPS2 Device

” for detailed information 

and instructions. 

 

Summary of Contents for IPS2 24 VDC


























Reviews:

No comments