21
After finishing work
Switching the vacuum cleaner off and
storage
1. After picking up
hazardous dust,
vacuum clean
the outside of
the cleaner.
2. Switch off the
vacuum cleaner
and pull the
mains plug out
of the socket.
3. Wind up the
power cord
and hang it on the handle.
4. Empty the tank and clean the vacuum cleaner.
5. After picking up liquids: Store the upper section
of the cleaner separately so that the filter element
can dry.
6. Store the vacuum cleaner in a dry room where it
is protected from unauthorized use.
Maintenance
Maintenance plan
After
As
finishing
required
work
Replacing the waste bag
•
Replacing the filter bag
•
Replacing filter element
•
Replacing filter element
•
Emptying dirt tank after
picking up liquids
•
Maintenance work
Replacing the waste bag
Clean the cleaner thoroughly before replacing the
waste bag – see section “Cleaning the filter element”.
During the following work, ensure that dust is
not unnecessarily spread around. Wear a P2
breathing mask.
1. Remove the upper part of the vacuum-cleaner.
2. Release the fastening catch (1) and remove the
washer from the container (2).
3. Close the waste bag using the cable connector.
4. Dispose of the vacuumed waste in accordance
with the law.
5. Insert a new filter bag into the cleaned tank as
described in the instructions enclosed.
Replacing the filter bag
During the following work, ensure that dust is
not unnecessarily spread around. Wear a P2
breathing mask.
1. Open the
retaining clamps
and remove the
upper section of
the cleaner from
the dirt tank.
2. Carefully remove
the filter bag
connection from
the inlet fitting.
3. Close the filter
bag connection
with the slide.
4. Dispose of the filter bag in accordance with legal
regulations.
5. Place a new filter bag into the cleaned tank as
described in the instructions (printed on the filter
bag).
IMPORTANT:
Press the filter bag connection on the
inlet fitting as far as possible.
Replacing filter element
During the following work, ensure that dust is
not unnecessarily spread around. Wear a P2
breathing mask.
1. Open the
retaining clamps
and remove the
upper section of
the cleaner from
the dirt tank.
Lay the upper
section of the
cleaner down
with the filter
element facing
upwards. Do not
place the upper
section of the cleaner on the guard (1) and do not
damage the filter element.
2. Open the bar handle (2) and remove it.
3. Remove the filter holder (3).
3
Summary of Contents for VCP 700 E-L
