19
Connecting electrical appliances
To comply with regulations, only approved dust
producing tools should be connected. The maximum
power consumption of the connected power tool is
stated in section “Technical data”.
1.
Ensure that the electrical appliance is
switched off.
2. Connect the electrical appliance to the appliance
socket on the control panel.
Switching on the vacuum cleaner
Switch position MAN
1. Turn the switch
to position MAN.
The vacuum
cleaner motor
starts.
VCP 700 E-M
The hose diameter and the setting for the suction
hose diameter must be the same.
Hose
∅
Hose diameter setting
∅
27
∅
27
∅
32
∅
32
∅
36
∅
36
∅
50
∅
50
Switch position AUTO
Before switching
the switch to posi-
tion AUTO, ensure
that the tool
connected to the
appliance socket is
switched off.
1. Turn the switch
to position
AUTO. The
vacuum cleaner
motor starts
when the connected appliance is switched on.
2. When the power tool is switched off the vacuum
cleaner continues to run for a short moment so
that any dust in the suction hose is conveyed to
the safety filter bag.
VCP 700 E-M
The hose diameter and the setting for the suction
hose diameter must be the same.
Hose
∅
Hose diameter setting
∅
27
∅
27
∅
32
∅
32
∅
36
∅
36
∅
50
∅
50
Suction power control
The motor speed
and the suction
power can be
varied with the suc-
tion power control.
This allows precise
adaptation of the
suction power for
different cleaning
tasks.
Check volume flow monitor
Before picking up dust with maximum room
concentration values:
1. Check that all the filters are present and properly
fitted.
2. When the motor is running, hold the suction hose
shut. An acoustic warning sounds after approx.
1 second.
Acoustic warning (VCP 700 E-M only)
For safety reasons, an acoustic warning sounds if
the air speed in the suction hose drops to below
20 m/s. See section “Troubleshooting”.
Cleaning the filter element
To ensure that suction performance is always at its
best, the filter element is automatically cleaned
during operation.
We recommend complete cleaning if the filter ele-
ment becomes extremely dirty.
After picking up harmless dust using the waste bag.
1. Switch off the vacuum cleaner
2. Close the nozzles or suction hose opening with
the palm of your hand.
3. Turn the switch to position MAN and let the
cleaner operate for approx. 10 seconds with the
suction hose opening closed.
10 sec.
Summary of Contents for VCP 700 E-L
