Proteus PEC-4650, Owner'S Manual

Page: 3 / 8

THE APPLIANCES ARE NOT FOR CHILDREN UNDER 14 YEARS OF AGES.
THE PEDAL CRANK TRAINING EQUIPMENT OF CLASS B AND C IS NOT
SUITABLE FOR THERAPEUTIC PURPOSES.
REPLACED DEFECTIVE COMPONENTS IMMEDIATELY AND KEEP THE
EQUIPMENT OUT OF USE UNTIL REPAIR
.
THE MOST SUSCEPTIBLE TO WEAR PARTS ARE
DRUM MAGNETIC WHEEL
MOTOR
BELT
STEP 1. FIT FRONT STABILIZER ( 2 ) TO THE FRAME ( 1 ) WITH CARRIAGE BOLTS ( 27 ) &
WASHERS ( 29 ) & NUTS ( 33 ), NOTE TO PREVENT HEAD OF CARRIAGE BOLTS ( 27 )
FROM DAMAGING FLOOR, DIMPLED SQUARE HOLES ON STABILIZER ( 2 ) MUST BE
FACING DOWN. ATTACH REAR STABILIZERS ( 3 ) TO REAR SIDE OF MAIN FRAME
( 1 ). FASTEN WITH BOLTS ( 28 ) WASHERS ( 29 ).
STEP 2.
a. ATTACH PEDALS ( 18 / 19 ) TO PEDAL CRANKS, ( PEDALS MARKED "L" AND "R"
INDICATES LEFT AND RIGHT SIDE OF BIKE. MAKE SURE NOT TO MIX IT UP ).
b. LEFT PEDAL HAS LEFT-HAND THREAD AND MUST BE TURNED
COUNTERCLOCKWISE ( CCW ) TO ATTACH, RIGHT PEDAL HAS RIGHT-HAND
THREAD, MUST BE TURNED CLOCKWISE ( CW ) TO ATTACH.
STEP 3. ATTACH SADDLE ( 20 ) TO SADDLE PLATE OF SEAT POST ( 04 ). FASTEN IT WITH
SPRING WASHERS ( 31 ) AND NYLON NUTS ( 32 ).
SLIDE SEAT POST ( 04 ) TO SEAT POST BOOT ( 21 ), THEN ATTACH TO MAIN FRAME
( 01 ). ADJUST THE HEIGHT OF THE SEAT BY THE KNOB ( 26 ). TIGHTENED THE
KNOB FIRMLY AFTER ADJUSTMENT.
STEP 4. CONNECT MONITOR CABLE A ( 9, FROM END OF #5 HANDLEBAR POST ) AND
MONITOR CABLE B ( 10, FROM MAIN FRAME ), THEN FIT HANDLEBAR POST ( 5 ) TO
MAIN FRAME WITH BOLTS ( 28 ) AND WASHERS ( 29 ),
STEP 5. ASSEMBLE HANDLE BAR ( 06 ) ONTO HANDLE BAR POST ( 05 ), FIX WITH WASHERS
( 29 ) AND BOLTS ( 28 ),
STEP 7. CONNECT MONITOR CABLE A ( 9, TOP OF HANDLEBAR POST ) TO THE MONITOR
( 08 ), THEN ATTACH MONITOR ( 08 ) TO THE MONITOR MOUNTING PLATE ( AT TOP
OF HANDLEBAR POST ) WITH SCREWS ( 22 )..
NOW THE ASSEMBLY OF THE PROGRAMMABLE MAGNETIC CYCLE IS DONE,
PLEASE NOTE WITH THE FOLLOWING INFORMATION BEFORE USE, THE MACHINE
IS REQUESTED TO USE AC ADAPTER, WHICH SHOULD BE WITH OUTPUT 9V / 1000
MA, PLEASE ALSO REFER TO MONITOR INSTRUCTION FOR THE PROPER
SPECIFICATION INFORMATION.
BEFORE YOU BEGIN
IMPORTANT: READ ALL INSTRUCTIONS CAREFULLY. ASSEMBLE THE UNIT IN ACCORDANCE
WITH THE STEPS IN THE MANUAL. LAY OUT ALL PARTS ON THE FLOOR AND
CHECK IF YOU HAVE ALL THE PARTS INCLUDED COMPLETELY BEFORE
BEGINNING ASSEMBLY. IN CASE OF A DISCREPANCY, PLEASE CALL THE
CUSTOMER SERVICE DEPARTMENT OF THE STORE FOR HELP.
NOTE: SOME PARTS MAY BE FACTORY PRE-ASSEMBLED.
TOOLS REQUIRED FOR ASSEMBLY
ONE ADJUSTABLE WRENCH, A PHILIPS HEAD SCREWDRIVER AND A ALLEN KEY
ASSEMBLY
- 2 -
IMPORTANT : READ ALL STEPS BEFORE ATTACHING PEDALS