background image

3.4.2 LIMIT SWITCH IN OPENING

Give an opening command. Check the store opera�on and make the according adjustments if necessary.

To set the limit switch, plug the provided key into the according fixing points. If you wish to increase the run of 

the store/awning, turn to “+”, while if you wish to decrease it turn to “-“.

The below diagrams show how to adjust the available systems, opening se�ng 

(possible adjustments for motor RH and LF posi�oned):

A�er fixing the opening and closing posi�ons, test the store/awning opera�on to check the correct run. 

Any further adjustments shall be carried out by the provided hexagonal key.

3.5 AWNINGS

Ø 70 adapters are available for awnings. Item code MTPR01.

So far the assembly a�end the awning manufacturer’s instruc�ons.

So far the wiring and limit switch adjustment a�end the store installa�on manual.

PROTECO Srl is liable for any manufacture fault on tubular motors, electrical components and accessories during 

3 years from manufacture date. 

PROTECO Srl responds for repairing within the warranty terms, a�er inspec�on by its technical staff. The returned 

faulty system will remain a Proteco’s property.

Use of the product must be restricted to its intended use. Any other use shall be considered out of the warranty. 

Installa�on and maintenance are charged at the person who carries out the installa�on.  

Use only Proteco’s original spares. Users are strictly forbidden to carry out any changes on the system. 

PROTECO Srl is not liable for any damage resul�ng from improper, wrongful or unreasonable use.

The return costs are at customer’s charge.

PROTECO Srl Via Neive 77, 12050 Castagnito (CN) Italia

The warranty doesn’t respond when:

7

4. WARRANTY

The chosen system doesn’t comply with the features of the store or awning

Prescrip�ons contained into the installa�on manual are disrespected

The item has been used/stored in unproper condi�ons

The item has been repaired, modified, altered

The item has been wrongly used or neglected

The manufacture label is damaged or is missing

The bad opera�on is due to oxida�on, overvoltage, insects, animals

Summary of Contents for PTP45











Reviews: