Pro's Kit GE-631, Assembly & Instruction Manual

Page: 8 / 27

4
https://youtu.be/opxoEtfa6Bg
P17
B14
P17
12
E2
P9
O
型環
(黑色)
O
型環
(黑色)
P9
B14
A3
E2
1 2 3
C5
使用
C5
協助將
P9
放到
E2
2
1
P4
5
6
氣 閥 組 裝
重要! 請確認
P17
的組裝方向，以免漏氣。
使用
B14
安裝
P9
將
P17
壓到底(如圖 )
確認
P9 O
型環平貼閥門
1
1
將
P17
推到頂(如圖 )
並確認
P9 O
型環平貼閥門
2
2
將
P4
直立於桌上，
將
B14
壓入
P4
(如圖示)
請仔細依循以下安裝方式，避免漏氣。
如果 P9 O 型環並未如上圖平貼閥門，請回到步驟 6 重做。
A3
Snap E2 to A3 entirely to avoid
air leakage.
4
將
E2
壓到底
將
A3
直立於桌上，並將
E2
平放於
A3
上。
E2
A3
1 2
影片示範
請掃描
QR code
觀看影片，可幫助您組裝更順暢。
O-ring
(Black)
O-ring
(Black)
Use C5 to assist you in setting P9
to E2 entirely.
Ensure the direction of two P17 to
avoid air leakage.
Use B14 to assist
you in setting two P9
entirely.
Push P17 to the bottom
(as per Fig ) and make
P9 to set flatly.
Push P17 to the top (as per Fig )
and make P9 to set flatly.
Straight P4 on the
table, cap B14 to P4
as shown .
If P9 (O-Ring) was set improperly as shown in above
wrong fig, re-do step 6 again.
Straight A3 on the table,
and put E2 on A3 flatly.
Press down
E2 to A3 entirely.
Video Tips
Scanning the QR code to help you assemble below steps smoothly.
Vale Assembly
Pay close attention to the following
steeps correctly to avoid air leakage
https://youtu.be/pgkLWs-0nig
13
1
2
P12
D4
D4
1
2
P17
影片示範
請掃描
QR code
觀看影片，可幫助您組裝更順暢。
紅色活塞帽
(
大
)
當
D4
推入時，請確認
P17
是否
依照箭頭指示方向移動。
當
D4
拉回時，請確認
P17
是否
依照箭頭指示方向移動。
用手指堵住突起孔
推入D4
D4
推入時應有阻力，無法輕易
推入。
漏 氣 測 試 ─ 氣 閥 Air Leakage Testing – The Valve
Red Cap (Big)
Seal the hole of the boss side with a finger.
Push in the D4.
Make sure that both P17 move to the
direction indicated by the arrows when
the D4 is pushed in.
Make sure that both P17 move in the
direction indicated by the arrows when
the D4 is pulled back.
Confirm that the D4 cannot be
pushed in easily.
Video Tips
Scanning the QR code to help you assemble below
steps smoothly.