manualshive.com logo in svg

PRONAR T740, Manual

Share
Download
PRONAR T740 Manual Download Page 6

3 

CONSTRUCTION AND PRINCIPLE OF OPERATION  

3.1

 

3.1

 

SPECIFICATION 3.2

 

3.2

 

CHASSIS 3.3

 

3.2.1

 

DRAWBAR EYE 

3.5

 

3.2.2

 

TRAILER SUPPORT 

3.5

 

3.3

 

LOAD BOX 

3.7

 

3.4

 

FRONT CONVEYOR 

3.9

 

3.5

 

FRONT CHAIN TRANSMISSION 

3.11

 

3.6

 

FRONT GEAR WHEEL TRANSMISSION 

3.13

 

3.7

 

REAR CHAIN TRANSMISSION 

3.14

 

3.8

 

WORKING BRAKE 

3.15

 

3.9

 

PARKING BRAKE 

3.20

 

3.10

 

TURNING INTERLOCK HYDRAULIC SYSTEM 

3.21

 

3.11

 

HYDRAULIC SYSTEM SLIDE BOLT AND CONVEYOR 

3.22

 

3.12

 

HYDRAULIC CLUTCH SYSTEM 

3.24

 

3.13

 

ELECTRIC LIGHTING SYSTEM 

3.27

 

3.14

 

ELECTRIC WEIGHING SYSTEM INSTALLATION 

3.29

 

4 

CORRECT USE  

4.1

 

4.1

 

PREPARING FOR WORK BEFORE FIRST USE 

4.2

 

4.2

 

ATTACHING TO TRACTOR 

4.5

 

4.3

 

TRANS-SHIPMENT TRAILER SUPPORT OPERATION 

4.7

 

4.4

 

LOADING 4.9

 

4.5

 

SECURING LOAD 

4.10

 

4.6

 

TRANSPORTING THE TRAILER 

4.11

 

4.7

 

UNLOADING 4.13

 

4.8

 

DISCONNECTING FROM TRACTOR 

4.15

 

Summary of Contents for T740









































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands