manualshive.com logo in svg

Prominence Home 51484, Owner'S Manual, Page: 10 / 15

Share
Download
Prominence Home 51484 Owner'S Manual Download Page 10

10

ASSEMBLY INSTRUCTIONS

15. Remove one of the three fitter plate screws 

preassembled to the fitter plate and loosen the other two 

but do not remove. Connect the 9-pin connector from 

the fitter plate to the 9-pin connector from the light kit. 

Align the keyhole slots in the light kit with the loosened 

screws in the fitter plate. Turn light kit clockwise and 

replace the previously removed fitter plate screw. Tighten 

all screws.

Light Kit

Light Kit

Glass Bowl

Fitter Plate 

Screw

Fitter 

Plate

9-pin 

Connector

Bulb

15

16

17

Light Kit

16. Install the E-26 base LED bulbs into the sockets on the 

light kit.

Important:

 Make sure you allow the bulbs and light kit to 

cool before you replace the bulbs.

17.  Attach the glass bowl to the light kit by twisting 

the glass bowl tightly in a clockwise direction until it is 

secure. 

CAUTION: 

Avoid cross-threading the glass during 

installation. Improper installation could cause the glass 

bowl to be difficult to remove or fall, which could cause 

serious injury.

Summary of Contents for 51484
















Reviews:

No comments