WIRING FUNCTIONS
C"
1nnm1
◊
-t
"
0 "E
N N
0
C
1'
e
.,
J
>-
Cl'.
D..
�
0)
--<
<(
Cl'.
1
1
t:
::J
<(
u u
a.
�
""Cl
""Cl
""Cl
z z
0
-1::
..c
0
0
0
>- >-
E
.,
.8
0)
0
0
0
.,
V,
V,
V,
_J
V,
ö1 ü: ü: ü:
_J
"'
,.._
"'
M
es
"'
,.._
"'
M
�
N N N N
:;;
,. ,.
'II,
'II,
'II,
'II,
'II,
'II,
'II,
:;;
.,
<(
,:,
0
M
u
-�
::i:
.,
,;
0
E
""Cl
,:,
�
0
0
.,
u
0 ::i: ::i:
Cl'.
"'
,.._
"'
M
:;;
'II,
'II,
'II,
'II,
0
00
"' ....
N
0
� �
:!
�
'.::
00
"' ....
N
N N N N N
'II,
'II,
'II,
'II,
'II,
'II,
'II,
'II,
'II,
'II,
'II,
'II,
'II,
'II,
'II,
�
w
C
N
:::;
°'
C
�
.E
"
� �
>-
C
:;;
C
.,
�
e
:;; :;;
�
"
E 0
.,
,:,
1
1
.,
C
C
<(
0
;::
0
u u
�
--< 0 0
0
u
0
::i:
z z
1'
�
1'
""Cl
u
D..
-1::
u u
.,
�
>- >-
0)
Ol
-"
"E
..c
V,
V,
ö1
0
.,
oll
�
�
·s
_J
0
ö1
J
0
C
u
ü:
.,
J
Cl'.
,:,
""Cl
0
0
0
0
ü: ü:
• POWER CABLE WIRING
1. Extend the
RED
wire to the + VBAT.
2. Properly connect the
BLACK
wire to the ground.
3. Connect the Functional Wires to your controller or switching
unit depending on the functions needed for application.
Applying +VBAT to any functional Wire will activate its
function.
-
PS
IT:
10106
dd
WARNING! Do not remove/change the
factory configured fuse attached at the
terminal of the RED wire without notice.
• WARNING LIGHTS
1.
Apply the + VBAT to #1, #2
or
#3 wire to activate
Mode 1, Mode 2, or Mode 3
2.Apply the + VBAT to #8 wire to activate Front Corners
3.Apply the +VBAT to #9 wire to activate Rear Corners
• FLASH PATTERNS
1. Connect the + VBAT to #1, #2
or
#3 wire to activate
Mode
1,
Mode2, or Mode 3
2. To advance the flash pattern by applying
#4
wire to a
+ VBAT momentary switch or top the
#4
wire to + VBAT
for 1 second.
3. Flash pattern will be reset when
#4
wire is connected to
+ VBAT for more than 5 seconds.
• ALLEY LIGHTS
1. Applying + VBAT to the #11 wire will activate the Left Alley.
2. Applying + VBAT to the #12 wire will activate the Right Alley.
3. Alley Lights override warning modes.
NOTE:
To configure the patterns of CRUISE ALL
MODE, T RAFFIC ARROW and TAKE DOWN, make
sure only one desired function wire is connected to
the + VBAT, and then top the #4 wire(flash pattern
wire) to + VBAT for 1 second.
• TRAFFIC ARROW
l. Apply +VBAT to the #18 wire will activate the Left Arrow.
2. Apply +VBAT to the #19 wire will activate the Right Arrow.
3. Apply +VBAT to the #20 wire will activate the Outside
in Arrow.
4. Centre out mode is activated by connecting both #18 & #19
wires to +VBAT.
5. With the desired traffic arrow wire connecting to + VBAT,
advance the pattern for each mode by tapping the
#4
wire to
+VBATfor 1 second.
NOTE:
Arrow function overrides all warning modes
an all rear-facing modules (not including corners).
• DIMMODE
Activate Dirn Mode by applying
#5
wire to +VBAT to operate
lighting at reduced intensity of 50% brightness. Traffic Arrow,
Takedown, alley lights and flood lights are not affected.
• FLOODMODE
Apply desired Flood Mode wire to +VBAT for activation of each
of 5 modes. Flood modes override flashing.
1. Activate Flood Front by applying #13 wire to +VBAT.
2. Activate Flood Front&Corners by applying #14 wire to + VBAT.
3. Activate Flood Rear by applying #15 wire to +VBAT.
4. Activate Flood Rear&Corners by applying #16 wire to + VBAT.
5. Activate Flood All by applying #17 wire to + VBAT.
• CRUIS E MODE
1. Activate the Cruise Corner mode by applying #6 wire to + VBAT.
2. Activate the Cruise All mode by applying #7 wire to +VBAT.
3. With
#7wire
connecting to +VBAT, apply#4to +VBATfor
1 second to advance the pattern of the Cruise All mode.
• TAKEDOWN
1. Apply +VBAT to the #10 wire to activate the factory configured
takedown function.
2. To advance the takedown pattern by tapping the
#4
wire to
+VBATfor l second.
• S TOP /TAIL/TURN
lf lig htbar is built with stop/tail/turn modules as specified at time of
order, separate control wires are included to control stop, tail, left
turn and right turn. ST T overrides flashing
1. Activate Stop Light by applying #21 wire to + VBAT.
2. Activate Tail Light by applying #22 wire to + VBAT.
3. Activate Left Turn by applying #23 wire to +VBAT.
4. Activate Right Turn by applying #24 wire to +VBAT.
• SMART PARK
Activate Smart Park by applying #25 wire to +VBAT to operate
lighting at reduced intensity of 50% brightness with 60 fpm
single flash.
NOTE:
Smart Park can only be activated when
Werning Model or Werning Mode2 is on.
P6
-
www.prolux-shop.com
www.prolux-shop.com
