Proline DWM12P Instruction Manual Download Page 13

13

Fuse blown, or the
circuit breaker 

tripped

Replace fuse or reset circuit breaker. Remove any other 
appliances sharing the same circuit with the dishwasher

Sound from soft food shredding action and detergent cup
opening.

Utensils are not secure
in the baskets or something
small has dropped into
the basket

To ensure everything is secured in the dishwasher.

Motor hums

Dishwasher has not been used regularly. If you do not use it 
often, remember to set it to fill and pump out every week, 
which will help keep the seal moist.

Improper detergent

Add 1 gallon of cold water to the tub. Close and latch the 
dishwasher, then drain out the water by slowly turning the
Dial until a drain period is reached. Repeat if necessary.

Spilled rinse agent

Always wipe up rinse agent
spills immediately.

Detergent with
colorant was used

Make sure that the detergent is the one without colorant.

Rinse agent dispenser
is empty

Make sure that the rinse agent dispense is filled.

Improper program

Improper rack loading

Make sure that the action of the detergent dispenser and 
spray arms are not blocked by large dishware.

Extremely hard water
Low inlet  
temperature
Overloading the 
dishwasher
Improper loading
Old or damp powder
detergent
Empty rinse agent 
dispenser
Incorrect dosage of 
 detergent

To remove spots from glassware:

Take out all metal utensils out of the dishwasher.
Do not add detergent.
Choose the longest cycle.
Start the dishwasher and allow it to run for about 
18 to 22 minutes, then it will be in the main wash.
Open the door to pour 2 cups of white vinegar 
into the bottom of the dishwasher.
Close the door and let the dishwasher complete
 the cycle. If the vinegar  does not work: Repeat 
as above, except use 1/4 cup (60 ml)of citric acid 
crystals instead of vinegar.

Some audible sounds are
normal

'

Make sure the dishwasher is turned on and the door is
closed securely.

Check that the water supply is connected properly and
the water is turned on.

Make sure the power cord is properly plugged into the 
wall socket.

Power supply is not
turned on

Water pressure is low

'

Overflow

The system is designed to detect an overflow. When it 
does, it shuts off the circulation pump and turns on the 
drain pump.

Select stronger program

Use only the special dishwasher detergent to avoid suds.

If this occurs, open the dishwasher and let suds evaporate.

Summary of Contents for DWM12P
















Reviews: