manualshive.com logo in svg

Prodys ProntoNet, User Manual

Share
Download
Prodys ProntoNet User Manual Download Page 51

 

Prontonet IP Decoder User Manual v5.4.1.1.doc

 

51

 

 

 

Voltage Out of Range 12 v Backup: 

The voltage from the backup power 

supply is out of range

.

 

 

Voltage  Out  of  Range  3.3  v  System: 

The  voltage  from  the  3.3  DC/DC  

converter is out of range

.

 

 

Voltage  Out  of  Range  5  v  System: 

The  voltage  from  the  5  DC/DC  

converter is out of range

.

 

 

Temperature Out of Range:

 The temperature is out of range

24

.

 

 

Fan Failure:

 The fun is activated if the internal temperature is over 34º. The 

Fan  Failure  alarm  will  be  activated  if  the  fun  doesn’t  work  when  the 
temperature is over this threshold.

 

 

 

LAN NOT Present: 

Not physical level detected in the LAN port. 

 

LAN  Traffic: 

The  LAN  traffic  is  higher  than  the  90%  of  the  capacity  of  the 

network. 

 

Decoder 1/2 Framed Lost

25

: The Line is connected but the decoder is not 

framed, but it was framed before. The alarm will be activated also if the unit 
is turned off. In this case, the alarm will indicate the date and time when the 
decoder  lost  the  synchronization,  that  is,  when  the unit  was  turned  off.  The 
alarm  will  be  activated  until  the  unit  is  framed  once  the  line  is  connected 
again. If the connection is not possible, the alarm will be marked as finished. 

 

Decoder  1/2  Not  Framed

:  The  Line  is  connected  but  the  decoder  is  not 

framed.  This  new  alarm  doesn’t  require  that  the  decoder  was  framed 
previously. For this reason, it is necessary to specify a window time to decide 
when  the  alarm  will  be  activated  once  that  the  NOT  FRAMED  condition  has 
been detected. 

 

 

Otherwise,  the  alarm  would  come  up  as  soon  as  the  connection  is 
established, given that the Decoder needs some time to detect the incoming 
compression mode. 
 

 

Line  Disconnected

:  Line  1/2  has  been  disconnected  unexpectedly, 

manually disconnected or both. 

 

General

: In internal hardware error was detected by the software. 

                                        

24

 The temperature is above 50ºC. 

25

 This alarm was introduced on version 4.7.1. 

Summary of Contents for ProntoNet




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands