manualshive.com logo in svg

Prodys ProntoNet, User Manual

Share
Download
Prodys ProntoNet User Manual Download Page 33

 

Prontonet IP Decoder User Manual v5.4.1.1.doc

 

33

 

 

 

 

IV.1.3.4.

 

Reboot System

 

 

A  new  option  to  reset  remotely  a  unit  was  included  in  the  SYS  configuration 
menu

13

. 

 
 
 

IV.1.3.5.

 

IP Codec Mode 

 
There  are  two  different  operation  modes:  SIMPLE  and  DOUBLE  mode

14

.  In 

SIMPLE mode, the unit will work as usual, that means, it can only establish one 
independent communication (Rx) via IP. In DOUBLE mode, the unit can establish 
two independent communications via IP. 
 

In DOUBLE mode over IP, the following restrictions will be applied: 

 
   

 1.- Encoder 1 and Encoder 2 can only be set in MONO. 

   

 2.- Encoder 2 (assigned to line 2)  can only be set in G722. 

 

IV.1.3.6.

 

Buzzer 

It is possible to enable/disable the buzzer from this option.  

                                        

13

 Available from version 4.7.1 onwards. 

14

 From version 4.5.0 onwards. 

Summary of Contents for ProntoNet




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands