background image

9

EN

Volere 22

Maintenance and Repair 

NOTICE:

 Some tape and adhesives may damage the 

finish on your boat. Always test applications on a non-

visible part (such as the finish under the seat on the front 

seat hatch) before applying anything to visible areas of 

your boat.

If needed, carefully remove dust from your boat with a 

clean, soft brush or a lint-free, soft cloth. 

The scale details on this boat are not intended for 

manipulation. If needed, apply only small amounts of 

thin CA (cyanoacrylate adhesive) to repair plastic scale 

features on your boat. CA may discolor. 

When parts are not repairable, see the Replacement 

Parts List for ordering by item number. For a listing of 

all replacement and optional parts, refer to the list at the 

end of this manual.

general Maintenance 

Before and at the end of each run, make sure that all 

screws are tight and that the propeller and rudder turn 

freely. Lubricate all moving parts with a light household 

oil after each boating session to prevent binding and 

corrosion. 

CAuTION: 

Always disconnect the battery from the 

ESC before performing maintenance on your boat 

or injury could result. 

CAuTION:

 Always replace the driveshaft when it is 

damaged or shows visible wear or failure resulting 

in injury and/or property damage can occur.

When You are finished

1.  Power off the ESC.
2.  Disconnect the battery.
3.  Power off the transmitter.
4.  Remove the battery from  

the boat.

Always store the boat open (without 

the hatch sealed) or moisture may 

allow mold and mildew to grow in 

the boat.

3

2

4

lubrication

Lubricating the driveshaft is vital to the life of the 

drivetrain. The lubricant also acts as a water seal, keeping 

water from entering the hull through the stuffing tube. 

1.  Only magnets hold the seat on the boat. Remove the  

seat from the cockpit by tipping it rearward and lifting 

it from the cockpit. 

2.  Lubricate the stuffing tube through the oil fill port near 

the motor coupler. Only a few drops of household 

light machine oil are needed. If desired, put a paper 

towel under the port to capture stray drops. 

1

Summary of Contents for PRB3050B



















Reviews: