ProBoat PRB08029 Owner'S Manual Download Page 14

Problem

Possible Cause

Solution

Boat will not respond 
to throttle but responds 
to other controls

Throttle channel is reversed

Reverse throttle channel on transmitter

Extra noise or extra 
vibration

Damaged propeller, shaft or motor

Replace damaged parts

Propeller is out of balance

Balance or replace propeller

Reduced runtime or boat 
underpowered

Boat battery charge is low

Completely recharge battery

Boat battery is damaged

Replace boat battery and follow battery instructions

Blocking or friction on shaft or propeller

Disassemble, lubricate and correctly align parts

Boat conditions may be too cold

Make sure the battery is warm (above 10º C
[50º F]) before use

Battery capacity may be too low for conditions

Replace battery or use a larger capacity battery

Too little lubrication on driveshaft

Fully lubricate driveshaft

Vegetation or other obstacles block the 
propeller

Remove vegetation or obstacles from propeller

Boat will not Bind 
(during binding) to 
transmitter

Transmitter is too near boat during binding 
process

Move powered transmitter a few feet from boat, 
disconnect and reconnect battery to boat

Boat or transmitter is too close to large 
metal object, wireless source or another 
transmitter

Move the boat and transmitter to another location 
and attempt binding again

Another compatible transmitter in bind 
mode within range of the receiver

Power off all compatible transmitters except the one 
you are trying to bind

Boat battery/transmitter battery charge is 
too low

Replace/recharge batteries

ESC switch is off

Power on ESC switch

Boat will not connect 
(after binding) to 
transmitter

Transmitter is too near boat during 
connecting process

Move powered transmitter a few feet from boat, 
disconnect and reconnect battery to boat

Boat or transmitter is too close to large 
metal object, wireless source or another 
transmitter

Move boat or transmitter to another location and 
attempt to connect again

Boat battery/transmitter battery charge is 
too low

Replace/recharge batteries

ESC switch is off

Power on ESC switch

Boat tends to dive in the 
water or takes on water

The boat hull is not completely closed

Dry out the boat and ensure the hatch is fully closed 
on the hull before returning the boat to the water

Center of gravity is too far forward

Move batteries back in the hull

Controls reversed

Transmitter settings are reversed

Do the Control Direction Test and adjust controls on 
transmitter appropriately

Motor overheats 

Blocked water cooler lines

Clean, unkink or replace water lines

Motor power pulses 
then motor loses power

Weather conditions might be too cold

Postpone until weather is warmer

Battery is old, worn out or damaged

Replace battery

Boat moves forward or 
backward without input 
from user

Throttle trim on transmitter not centered

Adjust throttle trim to center (12 o’clock)

Boat does not drive 
straight

Steering trim on transmitter not centered Adjust steering trim so vehicle drives straight

No steering or lack of 
steering

Steering rate not adjusted correctly

Adjusts steering rate (ST RATE) knob on 
transmitter to desired steering throw

Servo failed

Contact Horizon Product Support

No throttle or lack of 
throttle

ESC failed

Contact Horizon Product Support

Motor failed

Contact Horizon Product Support

ESC emits a continues 
tone when powered on

Throttle trim not centered

Center throttle trim on transmitter

Troubleshooting Guide

14

EN

®

Summary of Contents for PRB08029




















Reviews: