background image

4

    WARNING: 

To reduce the risk of serious injury, read all important precautions and 

instructions in this manual and all warnings on the weight bench before using the weight bench. 

ICON assumes no responsibility for personal injury or property damage sustained by or through the 

use of this product.

IMPORTANT PRECAUTIONS

1.  It is the responsibility of the owner to 

ensure that all users of the weight bench are 

adequately informed of all precautions.

2.  Before beginning any exercise program, 

consult your physician. This is especially 

important for persons over the age of 35 or 

persons with pre-existing health problems. 

3.  The weight bench is not intended for use 

by persons with reduced physical, sensory, 

or mental capabilities or lack of experience 

and knowledge, unless they are given super-

vision or instruction about the use of the 

weight bench by someone responsible for 

their safety.

4.  Use the weight bench only as described in 

this manual. 

5.  The weight bench is intended for home use 

only. Do not use the weight bench in any 

commercial, rental, or institutional setting.

6.  Keep the weight 

bench

 indoors, away from 

moisture and dust. Place the weight 

bench

 

on a level surface, with a mat beneath it to 

protect the floor or carpet. 

7.  Make sure that there is enough clearance 

around the weight 

bench

 for the exercises 

that you will do. 

8.  If you will use resistance bands (not 

included) with the rack, bolt the rack to 

the floor using the holes in the bases (see 

page 6 to identify the bases).

9.  Inspect and properly tighten all parts each 

time the weight bench is used. Replace any 

worn parts immediately. 

10. Keep children under age 16 and pets away 

from the weight bench at all times.

11. Wear appropriate clothes while exercising; 

do not wear loose clothes that could become 

caught on the weight bench. Always wear 

athletic shoes for foot protection.

12. Keep hands and feet away from moving parts.

13. Make sure that the adjustment knobs and the 

curl knob are fully engaged before you use 

the weight bench. 

14. The weight bench is designed to support a 

maximum user weight of 300 lbs. (136 kg). 

Do not place more than 100 lbs. (45 kg) of 

weight, including a barbell, on the curl frame. 

Do not place more than 310 lbs. (141 kg) of 

weight, including a barbell, on the weight 

rests. Do not place more than 150 lbs. (68 kg) 

of weight on each weight tube. Note: See 

page 6 and page 7 to identify the curl 

frame, the weight rests, and the weight 

tubes. The weight bench does not include 

weight plates or a barbell.

15. Over exercising may result in serious injury 

or death. If you feel faint, if you become short 

of breath, or if you experience pain while 

exercising, stop immediately and cool down.

Summary of Contents for Carbon Strength Olympic System

























Reviews: