background image

-21-

A : Display

B : Touch Panel

C : Status LED

1

Part Names

Color

Indicator

Operation

Mode 

*1

Controller

Operation Mode 

*2

Green

ON

OFFLINE

--- 

*3

ON

In operation

RUN

Flashing In operation

ST OP

Red

ON

In operation

Major Error

Color

Indicator

Orange

ON

Meaning

Backlight burnout has occurred.

*1 Operation mode includes Display, SIO Com-

munication and touch key features.

*2 Includes the performance of ladder circuit

program features.

*3 Changing to OFFLINE will release and stop

ladder circuit program features.

Front

Rear

Bottom

D : Power Input Terminal Block
E : Expansion Unit Interface
F : CF Card Access LED
G : Serial Interface (Dsub 25-pin)
H : Tool Connector
I

: Expansion Serial Interface
(Dsub 9-pin)

J

: Screw Lock Terminal Block

  (6-pin)

K : Flex Network Status LED

 Inside the CF Cover

N

M

L

J

I

H

G

E

F

D

A,B

C

Right Side

Left Side

K

L : Ethernet Interface
M : CF Card Cover
N : CF Card Slot (inside cover)

a

b

LED

Status

Contents

a:RUN
(GREEN)

T urns on when com m -
unication is enabled.

b:ERR
(RED)

T urns on when failure
occurs in connected I/O
Unit.

Summary of Contents for GLC2300-LG41-24V















Reviews: