Princess 332945, Manual

Page: 12 / 72

12
EN
The crevice nozzle (16) can be mounted to the
hose (8) or to the extension tube (10).
To mount the crevice nozzle to the hose •
(8), insert the hose inlet (21) into the
crevice nozzle (16).
To mount the crevice nozzle to the
•
extension tube (10), insert the tube inlet
(23) into the crevice nozzle (16).
To remove the crevice nozzle, pull the
•
crevice nozzle (16) from the hose inlet (21)
or the tube inlet (23).
Mounting and removing the brush
nozzle (fig. D & E)
The brush nozzle (17) can be used for
vacuuming tables, desks and shelves.
The brush nozzle (17) can be mounted to the
hose (8) or to the extension tube (10).
To mount the brush nozzle to the hose (8), •
insert the hose inlet (21) into the brush
nozzle (17).
To mount the brush nozzle to the
•
extension tube (10), insert the tube inlet
(23) into the brush nozzle (17).
To remove the brush nozzle, pull the brush
•
nozzle (17) from the hose inlet (21) or the
tube inlet (23).
Use
Unwinding and rewinding the
mains cable (fig. A)
The mains cable rewind button (2) can be
operated by hand or foot.
Before you proceed, we would like you to
focus your attention on the following notes:
- Do not unwind or rewind the mains cable
while the appliance is switched on.
- Always hold the mains plug to unwind the
mains cable. Never pull the mains cable.
Before use, hold the mains plug and •
unwind a sufficient length of the mains
cable from the back of the appliance.
After use, press the mains cable rewind
•
button (2) to rewind the mains cable back
into the appliance.
Manually guide the mains cable to make
sure that it does not swing back. Make sure
that the mains plug is correctly located.
Adjusting the length of the tube
(fig. E)
Keep the locking knob (25) pressed and •
slide the extension tube (10) to the required
position.
Release the locking knob (25).
•
Adjusting the suction nozzle (fig. F)
The floor surface selector (13) can be set to
adjust the suction nozzle (12) to the required
floor surface. The floor surface selector (13)
can be operated by hand or foot.
For vacuuming on laminates, tiles, etc., •
press the corresponding part (A) of the
floor surface selector (13).
For vacuuming on carpets, press the
•
corresponding part (B) of the floor surface
selector (13).
Switching on and off (fig. A)
The on/off button (1) can be operated by
hand or foot.
To switch on the appliance, press the •
on/off button (1).
To switch off the appliance, press the
•
on/off button (1) again.
Adjusting the suction force (fig. A)
The speed control switch (3) can be used to
adjust the suction force.
Set the speed control switch (3) to the •
required position:
- For vacuuming on hard surfaces
(e.g. floors), set a high suction force.
- For vacuuming on soft surfaces
(e.g. upholstery), set a low suction force.
Adjusting the airflow (fig. A)
The airflow can be adjusted using the airflow
control switch (11).
To adjust the airflow, set the airflow control •
switch (11) to the required position.
Carrying the appliance (fig. A)
The appliance can be carried using the
handgrip (5).
Raise the handgrip (5) into position. •
Carry the appliance using the handgrip (5). •