background image

Printed in USA 10/10 © 2010

2

541-531revD-EN

Product Holding Bin
DHB-BK41/43

Safety Information

Indicates information important to the proper operation of the unit. 
Failure to observe may result in damage to the equipment and/or 
severe bodily injury or death.

Indicates information important to the operation of the unit. Failure to 
observe may result in damage to the equipment.

WARNING

CAUTION

Installation

A. Remove the unit from the carton and inspect for signs of damage. If 

there is damage to the unit:

• notify the carrier within 24 hours of delivery
• save carton and packaging materials for inspection purposes
• contact your local dealer, or if purchased directly, the Prince Castle 

Sales Department at 800-722-7853 or 1-630-462-8800 to arrange for a 
replacement unit.

NOTE: When installing this unit, the ambient temperature at the mounting 
site should not exceed 100°F.

B. Place the bin on a counter and seal the base to the counter with food-

approved sealant.

C. Plug the power cord into the bin and connect the plug into the proper 

electrical outlet (15 amp, 120 Volt). All connections must be in 
accordance with local electrical codes and any other applicable codes.

NOTE: The electrical receptacle should be a dedicated outlet. No other 
equipment should be operating on the line (refrigerators, fryers, etc.).

D. If used, plug the Prince Castle Retro Bun Steamer BK-RSTMC timer 

data cable into the blue plug jack (external) located on the rear of the 
Prince Castle holding bin. If cable from timer is too short, use Prince 
Castle Extender Cable Kit, P/N PC-COMEXT.

E. Install the racks, pans and pan covers into the cavities.
F. Turn the power switch to ON. Allow 30 minutes for warm-up.

NOTE: If the unit is to be networked with other Prince Castle units, a Retro 
Bun Timer may be connected to any one bin in the chain. Refer to 
CASTLENET COMMUNICATIONS NETWORK in this manual.

 

White Plug 

Jack (in from 

another unit)

Rear of PHU

Black Plug Jack 

(out to another 

unit)

Power Cord Inlet

Blue Plug Jack 

(Plug BK-RSTMC 

Retro Bun 

Steamer timer

data cable in here)

Retro Bun

Timer

BIN 1

BIN 2

BIN 3

Prince Castle reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to 
corresponding changes, improvements, additions or replacements for previously purchased equipment.

Summary of Contents for DHB-BK41/43















Reviews: