background image

 

HI ALARM

 

 

AUTO RST / MANUAL

 

 

AUTO RST:

  The high level alarm is automatically cleared as the    

 

 

 

 

level drops below the HI ALARM set point. 

 

 

MANUAL:

 

The alarm will remain on until the RESET button is    

 

 

 

 

pressed by the operator.

 LO 

ALARM 

 

AUTO RST / MANUAL

 

 

AUTO RST:

  The low level alarm is automatically cleared as the    

 

 

 

 

level rises above the LO ALARM set point. 

 

 

MANUAL:

 

The alarm will remain on until the RESET button is    

 

 

 

 

pressed by the operator.

 MODE 

In 

PUMP 

 

mode, as the level value rises above a set point,  

 

 

 

the controller will switch 

ON

 the corresponding output relay and  

 

 

 

it will remain 

ON

 until the level drops below the set point (the  

 

 

 

PUMP 

 mode is used for pump down or emptying applica-  

 

  

tions).

 

    

In 

PUMP 

 mode, the relays turn 

ON

 as the level drops below  

 

 

 

the set points and remains 

ON

 until the level rises above the  

 

 

 

set point (the 

PUMP 

 

mode is used for pump up or filling    

 

  

applications).

 

RUN SIG  

USED/UNUSED

 

 

USED:

 

The pump run indication LEDs are dependent on input  

 

 

 

 

signals 1, 2, 3, 4 from motor starter auxiliary contacts. 

 

 

UNUSED:

 

The pump run indication LEDs are on when the output  

 

 

 

 

relays for pump control are energized.

 RES 

CTRS 

 

RESET ALL COUNTERS

 

 

 

 

Enter 12 in this field and all counters will be reset to    

 

 

  zero.

PRIMEX ™                                                                                            14                                                               SP6R-LSC Level Controller User Manual

Summary of Contents for SP6R-LSC





















Reviews: