PRIMERGY BX600 S3 Hardware Manual Download Page 55

Page: 55 / 143

PRIMERGY BX600 Management Blade Hardware Guide

4.2.11 Server Blade Group

All the Server Blades/Storage Blades installed in the chassis are shown in Server Blade group. The

power supply status and the keyboard/display/mouse (KVM) select location are both shown as an icon at

the same time.

A Recovery group and a Blade Info group exist in every Server Blade and clicking on pages in these

groups displays the system setting page relating to that Server Blade. The following operations will be

performed for the selected Server Blade.

●

Recovery group

Recovery group performs the actions when an error occurs, CMOS backup/restore settings, power

supply settings and schedule and boot option settings.

• ASR, server blade

• Software Watchdog

Sets by ServerView.

• Boot Watchdog

Sets actions when the Server Blade OS boot fails. The Server Blade OS boot is monitored by

monitoring the interval between the end of Server Blade POST and the boot of ServerView agent.

If communication with ServerView agent does not begin during the timeout period (Watchdog

Time) after the Server Blade POST exits, an OS boot failure is detected and an action will be

executed. These following options exist for actions.

Icon

Description

Server Blade is powered OFF.

Server Blade is powered ON.

KVM is selected for this Server Blade but it is powered OFF.

KVM is selected for this Server Blade and it is powered ON.

Display/Parameter

Description

Boot Watchdog

This section explains the settings when OS boot fails.

• enable: monitor OS boot.
• disable: do not monitor OS boot.

Watchdog Time

Monitors OS boot failure according to the set time.
Watchdog time can be set to between 2–100 minutes and phased setting is possible.

Watchdog Action

Sets actions when OS boot fails.

• no-action: no action is taken.
• hard reset: reboots Server Blade.
• off: turn Server Blade off.
• graceful shutdown and power-cycle: the Server Blade is shut down, power is

temporarily turned off and back on again.

Maximum Restart

Retries

Sets how many times boot will be retried after OS boot fails.

• 0: will not retry
• 1–7: The set number of retries are performed.

Summary of Contents for BX600 S3
















































































































































Search results

Summary of Contents for BX600 S3

Reviews:

Related manuals for BX600 S3

Brands by name

Popular brands

PRIMERGY BX600 S3, Hardware Manual

Search results

Summary of Contents for BX600 S3

Reviews:

Related manuals for BX600 S3

Brands by name

Popular brands