background image

SAFETY GUIDELINES

The symbols below are used throughout this troubleshooting guide to identify warnings and important infor-
mation. It is very important for you to read what follows the symbols and understand it completely.

WARNING! Indicates a potentially hazardous condition

/

situation. Failure to follow designated

procedures  can  cause  either  personal  injury,  component  damage,  or  malfunction.  On  the
product, this icon is represented as a black symbol on a yellow triangle with a black border.

MANDATORY! These actions should be performed as specified. Failure to perform mandatory
actions  can  cause  personal  injury  and

/

or  equipment  damage.  On  the  product,  this  icon  is

represented as a white symbol on a blue dot with a white border.

PROHIBITED!  These  actions  are  prohibited.  These  actions  should  not  be  performed  at  any
time or in any circumstances. Performing a prohibited action can cause personal injury and

/

or equipment damage. On the product, this icon is represented as a black symbol with a red
circle and red slash.

© Pride Mobility Products Corp. 2010
Rev. A/January 2010/INFMANU3986

Summary of Contents for Victory 10






















Reviews: