background image

S A F E T Y   G U I D E L I N E S

WARNING! An authorized Pride Provider or a qualified technician must perform the initial setup 

of this power chair and must perform all of the procedures in this manual.

The symbols below are used throughout this owner’s manual and on the power chair to identify warnings and 

important information. It is very important for you to read them and understand them completely.

WARNING! Indicates a potentially hazardous condition/situation. Failure to follow designated 

procedures  can  cause  either  personal  injury,  component  damage,  or  malfunction.  On  the 

product, this icon is represented as a black symbol on a yellow triangle with a black border.

MANDATORY! These actions should be performed as specified. Failure to perform mandatory 

actions  can  cause  personal  injury  and/or  equipment  damage.  On  the  product,  this  icon  is 

represented as a white symbol on a blue dot with a white border.

PROHIBITED!  These  actions  are  prohibited.  These  actions  should  not  be  performed  at  any 

time or in any circumstances. Performing a prohibited action can cause personal injury and/or 

equipment damage. On the product, this icon is represented as a black symbol with a red circle 

and red slash.

Intended Use

The intended use of this Pride Mobility Products device is to provide mobility assistance to persons with mobility 

impairment who have the capacity to operate a motorized mobility power chair.

Regarding Devices for Prescription Use

CAUTION! Federal law restricts this device to sale by or on the order of a physician or 

other certified personnel licensed by the law of the State (US only) or region in which 

this personnel practices to use or order the use of the device.

Quick Reference Information

Copyright © 2022

INFMANU5238/Rev A/September 2022

NOTE: This owner’s manual is compiled from the latest specifications and product information available at 

the time of publication. We reserve the right to make changes as they become necessary. Any changes to our 

products may cause slight variations between the illustrations and explanations in this manual and the product 

you have purchased. The latest/current version of this manual is available on our website.

NOTE: This product is compliant with WEEE, RoHS, and REACH directives and requirements.

NOTE: This product meets IPX4 classification (IEC 60529).

NOTE: This product and its components are not made with natural rubber latex. Consult with the manufacturer 

regarding any after-market accessories.

Authorized Pride Provider:

Address:

Telephone:

Purchase Date:

Summary of Contents for Jazzy EVO 614 HD

































Reviews: