background image

..\Manuals\RCI-800-RF9 rev.B.doc 

                                                                                                          Page 10 of 10 

Cable & Antenna Selection & Installation:

 

 
The antenna is a very important component in a radio system.  Make sure you consult the factory for 
proper antenna selection for your project.  Cable leading from the radio to the antenna is just as 
important in establishing a reliable link.  Special low-loss cable is available to ensure minimal signal 
losses in the cable leading to the antenna.  This cable must be kept as short as possible.  We 
recommend purchasing the cable from Pribusin Inc. to ensure a good match for the entire system.  

Regular TV coaxial cable or even satellite dish coaxial cable will not work.

  Even ‘good’ TV cables 

have enormous losses at the high frequency of this radio. 
 
Line-of-Sight Installation: 
 
To achieve maximum operational reliability, all antennas in a system must 
be installed in a line-of-sight fashion.  This means that there are no 
obstructions between the host antenna and each of the remote antennas.  
This may require the antenna to be raised on a mast with some low-loss 
coaxial cable being installed.  We recommend coaxial cables be kept as 
short as possible and not exceed 100ft. 
 
In some cases a direct line-of-sight may not be established, but if there are 
solid structures such as buildings, tanks etc. in the vicinity, the signal may 
reflect off these surfaces and reach an antenna via an indirect path.  Such 
installations are not easy and are difficult to predict without on-site testing. 
 
 
Antenna Polarization: 
 
When installing antennas keep in mind that polarity matters.  Alignment for 
antennas depends on the type of antennas being used.  For example, if using 
omni-directional antennas, point them parallel to one another as shown in the 
diagram below.  Do not point them in different directions or the range of the 
antennas will be greatly diminished to the point where no transmission may 
take place. If using an omni-directional and a YAGI antenna, align them 
perpendicular to one another with the YAGI pointing towards the OMNI. If 
using YAGI antennas, align them facing one another as shown in the diagram 
to the right.  Placing them parallel to one another greatly diminishes the 
transmission between antennas.  
 

   

 

(YAGI-YAGI) 

       

 

 
 

 

 

  

 
 
 
 

  

 

         (OMNI-OMNI)  

 

                           (OMNI-YAGI)  

 
 
We suggest you consult Pribusin Inc. or your local Sales Rep. to discuss your antenna and cable 
requirements. 
 

Summary of Contents for RCI-800-RF9

















Reviews: